1. Manuals
  2. Brands
  3. Ranger Manuals
  4. Industrial Equipment
  5. RP-50FC
  6. Installation and operation manual

Ranger RP-50FC Installation And Operation Manual

High-speed oil filter crusher
Hide thumbs Also See for RP-50FC:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Operation Manual
Manual P/N 5900392 — Manual Revision C4 — March 2023
Model:
• RP-50FC
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
⚠
DANGER
High-Speed Oil Filter Crusher
IMPORTANT SAFETY INSTRUCTIONS, SAVE THESE INSTRUCTIONS! Read this
manual thoroughly before installing, operating, servicing, or maintaining this equipment.
Failure to follow the instructions and safety precautions in this manual can result in serious
injury or death. Make sure all other operators also read this manual. Keep the manual near
the product for future reference. By proceeding with installation and operation,
you agree that you fully understand the contents of this manual and assume
full responsibility for product use.
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free 1 (800) 253-2363
Tel: 1 (805) 933-9970
rangerproducts.com

Advertisement

Table of Contents
loading

Related Manuals for Ranger RP-50FC

Summary of Contents for Ranger RP-50FC

  • Page 1 High-Speed Oil Filter Crusher Installation and Operation Manual Manual P/N 5900392 — Manual Revision C4 — March 2023 Model: • RP-50FC Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. ⚠ IMPORTANT SAFETY INSTRUCTIONS, SAVE THESE INSTRUCTIONS! Read this DANGER manual thoroughly before installing, operating, servicing, or maintaining this equipment.
  • Page 2 Warranty. The BendPak Ranger warranty is more than a commitment to you: it is also a commitment to the value of your new product. For full warranty details and to register your new BendPak Ranger product, contact your nearest BendPak Ranger dealer or visit www.bendpak.com/support/warranty.

  • Page 3: Table Of Contents

    95 percent of the residual oil. This manual describes these models: • RP-50FC: High-speed oil filter crusher that uses a 208–230 VAC, 60 Hz, single phase motor. This motor is suitable for use in the United States. ⚠...
  • Page 4 ⚠ WARNING Always promptly clean any Hydraulic Fluid spills. If a leak is the source of the spill, do not use until the Hydraulic System is repaired. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...

  • Page 5: Shipping Information

    The Power Unit’s Motor is not constant duty; it cannot be run continuously. • Do not use the product while tired or under the influence of drugs, alcohol, or medication. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 6 Instead, contact an authorized repair facility, your distributor, or the Ranger Products Hotline at 1 (805) 933-9970. • BendPak Ranger recommends making a thorough inspection of the product at least once a year. Replace any damaged or severely worn parts, decals, or warning labels. Symbols Following are the symbols used in this manual: ⚠...

  • Page 7: Specifications

    208–230 VAC, 60 Hz, 1 Ph Components The following figure shows the major components of the unit. There are also components on the left side of the enclosure. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...

  • Page 8: Setup

    Socket head cap screw (4), M12 by 1.75 by 120, referred to as Screw B • HHB MM 8 by 35 (4), referred to as Screw C RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 9 Do not tighten nuts at this time. 2. Bolt the base frame vertical support bars to the reservoir base. Use Screw A with washer and nut. Do not tighten nuts at this time. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 10 Do not tighten nuts at this time. 4. Bolt the base frame legs to the vertical support bars. Use Screw A with washer and nut. Do not tighten nuts at this time. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 11 5. Stand up the base frame assembly and the reservoir base. Tighten all nuts. The Stand Assembly and Reservoir Base are now assembled. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 12 1. Remove the top of the enclosure, exposing the eye hitch. 2. Use the eye hitch to lift the enclosure onto the reservoir base. 3. Bolt the enclosure onto the base frame and reservoir. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 13 4. Bolt the enclosure to the vertical support bars on both sides. Use Screw A with one flat washer, two ridged washers, and one nut. The enclosure is now mounted to the base frame. Connecting the equipment: 1. Remove the rear panel of the enclosure. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 14 To make it easier to connect the cylinder hose, remove the top connector on the pressure switch; this allows it to be move around more freely. 3. Screw down the pressure switch. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 15 5. Attach the hydraulic fitting to the left and right sides of the motor. 6. Attach the 664 mm hose (on the left below) to the hydraulic fitting on the left side of the motor. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 16 Approved fluids are any general purpose ISO-32, ISO-46, or ISO-68 hydraulic oil or approved ATF fluids such as Dexron III, Dexron VI, Mercon V, Mercon LV, or any Synthetic Multi-Vehicle ATF. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 17 Wiring the RP-50FC to 220 VAC, 60 Hz, single phase: ⚠ DANGER All electrical work must be accomplished by a licensed Electrician in accordance with all applicable national and local electrical codes. Damage caused by improper electrical installation will void your warranty.
  • Page 18 4. Connect the longer, bigger red and blue wires to the Power Unit Box on the Power Unit. Note: You have to remove the screws on the Power Unit Box to connect the P5 wire. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 19 The figure below details the wiring connections for the RP-50FC. Not to scale. Many components not shown, for clarity. Multiple views combined into a single view. 5. Connect one end of the power cord to the top of the On/Off Breaker Switch, including the ground wire.
  • Page 20 8. Connect the foot pedal to the remote foot switches cable on the left side of the unit. 9. Install the left, right, and center grates into the reservoir base. The unit is now ready for operation. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...

  • Page 21: Operation

    To prevent the Power Unit components from overheating, we recommend taking 2-3 minute breaks after every half hour of use. The Power Unit’s Motor is not constant duty; it cannot be run continuously. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...

  • Page 22: Maintenance

    • Lubricate the sliding door on a regular basis to prevent the door from binding. • Keep the red Stop button clean and in working order. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...

  • Page 23: Troubleshooting

    If you continue to have an issue, visit bendpak.com/support or contact BendPak Technical Support, call (888) 856-5820, or email support@bendpak.com. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...

  • Page 24: Parts Diagrams

    Parts Diagrams RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 25 RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 26 RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 27 RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — Rev. C4 — March 2023...
  • Page 28 1645 Lemonwood Drive Santa Paula, CA 93060 USA bendpak.com © 2023 BendPak Inc. All rights reserved.

This manual is also suitable for:

5150401

Table of Contents