Ranger RP-50FC Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Ranger Manuals
  4. Power Tool
  5. RP-50FC
  6. Installation and operation manual

Ranger RP-50FC Installation And Operation Manual

High-speed oil filter crusher
Hide thumbs Also See for RP-50FC:
Table of Contents

Advertisement

Quick Links

Installation and Operation Manual
Revision B — March 2017 — Manual P/N 5900392
Model:
• RP-50FC
⚠
DANGER
High-Speed Oil Filter Crusher
Always operate this equipment as directed; failure to do so may
cause injury or death. Read the entire contents of this manual prior
to installation or operation. Make sure all other operators also read
this manual. By proceeding with setup and operation, you agree
that you fully understand the contents of this manual.
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free +1.800.253.2363
Tel: +1.805.933.9970
Fax: +1.805.933.9160
www.rangerproducts.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RP-50FC and is the answer not in the manual?

Questions and answers

Related Manuals for Ranger RP-50FC

Summary of Contents for Ranger RP-50FC

  • Page 1 High-Speed Oil Filter Crusher Installation and Operation Manual Revision B — March 2017 — Manual P/N 5900392 Model: • RP-50FC ⚠ Always operate this equipment as directed; failure to do so may DANGER cause injury or death. Read the entire contents of this manual prior to installation or operation.
  • Page 2 Warranty. The BendPak Ranger warranty is more than a commitment to you: it is also a commitment to the value of your new product. For full warranty details and to register your new BendPak Ranger product, contact your nearest BendPak Ranger dealer or visit www.bendpak.com/support/warranty.

  • Page 3: Table Of Contents

    20 percent of its size while removing up to 95 percent of the residual oil. More information about the full line of Ranger Products is available at www.rangerproducts.com. This manual is mandatory reading for all users of the RP-50FC, including anyone who sets it up, operates it, maintains it, or repairs it.

  • Page 4: Safety Considerations

    Make a visual inspection of the product before using it. Do not use the product if you find any missing or damaged parts. Instead, contact an authorized repair facility, your distributor, or the Ranger Products Technical Support Hotline at +1.805.933.9970. thorough •...

  • Page 5: Specifications

    BendPak Ranger assumes no liability for damages resulting from: • Use of the equipment for purposes other than those described in this manual. • Modifications to the equipment without prior, written permission from BendPak Ranger. • Damage to the equipment from external influences. •...

  • Page 6: Components

    Components The following figure shows many of the components of the RP-50FC. There are also components on the left side of the enclosure. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...

  • Page 7: Setup

    A plug to connect to the power unit’s electrical cord. Unpacking Use caution when unpacking the RP-50-FC components from their shipping containers. Consider unpacking the RP-50FC components in the area where you are going to assemble the unit. Screws Assembling the unit requires the use of several different types of screws: •...
  • Page 8 Assembly Your RP-50FC comes disassembled (to protect the components during shipping). The assembly process happens in multiple phases. Perform them in the order shown. Assembling the base frame: 1. Connect the left and right base frame support bars to the reservoir base. Use Screw A with washer and nut.
  • Page 9 3. Bolt the base frame support bars to the vertical support bars. Use Screw B with washer and nut. 4. Bolt the base frame legs to the vertical support bars. Use Screw A with washer and nut. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 10 5. Stand up the base frame assembly and the reservoir base. The base frame assembly and reservoir base are now assembled. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 11 1. Remove the top of the enclosure, exposing the eye hitch. 2. Use the eye hitch to lift the enclosure onto the reservoir base. 3. Bolt the enclosure onto the base frame and reservoir. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 12 4. Bolt the enclosure to the vertical support bars on both sides. Use Screw A with one flat washer, two ridged washers, and one nut. The enclosure is now mounted to the base frame. Connecting the equipment: 1. Remove the rear panel of the enclosure. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 13 2. Connect the cylinder hose to the pressure switch. Tighten the hose to the cylinder at the top. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 14 Use Screw C and two washers per screw to attach the anti-vibration pad. 5. Attach the hydraulic fitting to the left and right sides of the motor. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 15 6. Attach the 664 mm hose (on the left below) to the hydraulic fitting on the left side of the motor. 7. Attach the 758 mm hose (on the left above) to the hydraulic fitting on the right side of the motor. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 16 8. Add hydraulic oil to the motor. Attaching the wiring: 1. Wires labeled P6 and P7 connect to the control board and to terminals on the motor. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 17 The longer red and blue wires connect to the power unit box on the power unit. Note: You have to remove the screws on the power unit box to connect the P5 wire. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 18 4. Slide the other end of the power cord through the top of the tube on the vertical support bar (part of the frame) all the way through to the bottom, then connect it to an appropriate plug. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 19 6. Connect the foot pedal to the remote foot switches cable on the left side of the unit. 7. Install the left, right, and center grates into the reservoir base. The unit is now ready for operation. RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...

  • Page 20: Operation

    The correct way to press any of the control buttons is to firmly press and then release. Pressing holding the control buttons can cause damage to the unit. There are three control buttons on the RP-50FC: Start button, green. Activates the automatic pressing cycle. When pressed, the press ram •...

  • Page 21: Maintenance

    Using the Foot Pedals The foot pedals operate differently than the control buttons. To manually operate the RP-50FC using the foot pedals: 1. Make sure the foot pedals cable is connected to the left bottom side of the control box.

  • Page 22: Troubleshooting

    Warranty The BendPak Ranger warranty is more than a commitment to you; it is also a commitment to the value of your new product. For full warranty details and to register your new product, contact your nearest BendPak Ranger dealer and select the Ranger Warranty option.

  • Page 23: Parts Diagrams

    Parts Diagrams RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 24 RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 25 RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...

  • Page 26: Wiring Diagram

    Wiring Diagram RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...

  • Page 27: Maintenance Log

    Maintenance Log RP-50FC High-Speed Oil Filter Crusher P/N 5900392 — March 2017 — Rev. B...
  • Page 28 1645 Lemonwood Drive Santa Paula, CA 93060 USA © 2017 BendPak Inc. All rights reserved. www.bendpak.com...

Table of Contents