Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TQ TQMa64xxL
Summary of Contents for TQ TQMa64xxL
- Page 1 TQMaX4XxL User's Manual TQMaX4XxL UM 0100 11.04.2024...
-
Page 2: Table Of Contents
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page i TABLE OF CONTENTS ABOUT THIS MANUAL ................................. 1 Copyright and license expenses .............................. 1 Registered trademarks ................................1 Disclaimer ....................................... 1 Imprint ......................................1 Tips on safety ....................................2 Symbols and typographic conventions.......................... - Page 3 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page ii TQMaX4XxL interface ................................21 3.3.1 Pin assignment ................................... 21 3.3.2 Pinout TQMaX4XxL ................................... 22 SOFTWARE ....................................28 MECHANICS ....................................28 TQMaX4XxL dimensions and footprint ..........................28 TQMaX4XxL component placement ........................... 30 Protection against external effects ............................
- Page 4 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page iii TABLE DIRECTORY Table 1: Terms and Conventions ................................2 Table 2: AM64x derivatives (Source: Texas Instruments) ........................ 7 Table 3: AM243x derivatives (Source: Texas Instruments) ....................... 8 Table 4: Selecting the General Boot Configuration..........................
- Page 5 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page iv FIGURE DIRECTORY Figure 1: Block diagram AM6442 ................................4 Figure 2: Block diagram AM243x ................................5 Figure 3: Block diagram TQMaX4XxL ............................... 6 Figure 4: Block diagram Boot-Strapping ..............................9 Figure 5: Block diagram DDR3L SDRAM connection ........................
-
Page 6: About This Manual
User's Manual, or due to usage of erroneous or incomplete information, are exempted, as long as there is no proven intentional or negligent fault of TQ-Systems GmbH. TQ-Systems GmbH explicitly reserves the rights to change or add to the contents of this User's Manual or parts of it without special notification. -
Page 7: Tips On Safety
Handling and ESD tips General handling of your TQ-products The TQ-product may only be used and serviced by certified personnel who have taken note of the information, the safety regulations in this document and all related rules and regulations. A general rule is: do not touch the TQ-product during operation. This is especially important when switching on, changing jumper settings or connecting other devices without ensuring beforehand that the power supply of the system has been switched off. -
Page 8: Naming Of Signals
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 3 Naming of signals A hash mark (#) at the end of the signal name indicates a low-active signal. Example: RESET# If a signal can switch between two functions and if this is noted in the name of the signal, the low-active function is marked with a hash mark and shown at the end. -
Page 9: Brief Description
Page 4 BRIEF DESCRIPTION The TQMaX4XxL is a universal TQ-LGA mini module based on the TI Sitara family AM64x and AM243x processors with ARM Cortex A53, Cortex R5 and Cortex M4 cores. This User's Manual describes the hardware of the TQMaX4XxL Rev.020x and refers to some software settings. - Page 10 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 5 Figure 2: Block diagram AM243x (Source: Texas Instruments) All useful AM64x / AM243x signals are routed to the TQMaX4XxL pads. There are no restrictions for customers using the TQMaX4XxL with respect to an integrated customised design.
-
Page 11: Electronics
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 6 ELECTRONICS The information provided in this User's Manual is only valid in connection with the tailored boot loader, which is preinstalled on the TQMaX4XxL, and the BSP provided by TQ-Systems GmbH, see also section 4. -
Page 12: Pin Multiplexing
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 7 3.1.3 Pin multiplexing The pin multiplexing of the AM64x / AM243x permits to use many pins for different interfaces. The information provided in this User's Manual is based on the BSP provided by TQ-Systems GmbH. - Page 13 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 8 Table 3: AM243x derivatives (Source: Texas Instruments)
-
Page 14: Booting
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 9 Attention: Malfunction Please take note of the latest AM64x/AM243x errata (4). 3.2.2 Booting 3.2.2.1 Boot source The boot source is selected via the boot strapping pins of the AM64x / AM243x. The signals are directly routed to the LGA balls and will be available again as GPIO after reading the boot configuration. -
Page 15: Boot Device Emmc
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 10 3.2.2.2 Boot device eMMC Table 5: Boot device selection eMMC Boot configuration pin Setting TQMaX4XxL Port: MMCSD Port 0 (8 bit width) BOOTMODE[9] This bit must be set to 0... -
Page 16: Memory
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 11 Note: Update When designing a mainboard, it is recommended to plan a redundant update concept for software updates in the field. Furthermore, it is recommended to switch the conversion of the boot strap pins to high impedance after reading in. -
Page 17: Nor-Flash
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 12 3.2.3.3 NOR-Flash A NOR flash is available on the TQMaX4XxL as additional non-volatile memory. The used OSPI0 signals are not available to the pinout. Figure 7: Block diagram NOR-Flash The NOR-Flash variants Quad SPI Flash and Octal SPI Flash are usable. -
Page 18: Rtc
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 13 3.2.5 An optional RTC (NXP PCF85063A) can be equipped on the TQMaX4XxL. The connection is realized as follows: • The RTC can be supplied from the base board via V_RTC_IN. V_RTC_IN = 2.0 V to 5.5V •... -
Page 19: Secure Element
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 14 3.2.6 Secure Element A Secure Element Chip can optionally be fitted on the TQMaX4XxL. The connection can be seen in the following figure: Figure 10: Block diagram SEC The SE050C2HQ1/Z01 from NXP is used as the secure element. -
Page 20: Gpio
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 15 3.2.8.3 GPIO Besides their interface function, most AM64x / AM243x pins can also be used as GPIOs. Details are to be taken from the AM64x / AM243x Data Sheet (1) (2). -
Page 21: Serdes
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 16 3.2.8.5 SerDes The CPU has a SerDes lane, which can be used either as PCIe or USB3.0. The signals are directly accessible at the LGA pads. For more information please refer to the Reference Manual (3). -
Page 22: Uart
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 17 3.2.8.8 UART The TQMaX4XxL provides up to seven UART interfaces. UART0 and UART1 are routed to the TQMaX4XxL pads as primary functions with handshake signals. 3.2.8.9 The AM64x / AM243x provides up to two integrated CAN controller. The signals of both CAN controller are routed to the TQMaX4XxL pads as primary function. -
Page 23: Mcu_Porz
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 18 3.2.9.1.2 MCU_PORz The MCU_PORz signal is used to control a cold reset. Between the LGA balls MCU_PORz and the AM64x / AM243x MCU_PORz signal is an AND element and a supervisor, which keeps the signal at LOW during power sequencing and pulls it HIGH afterwards. -
Page 24: Power Supply
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 19 3.2.11 Power supply 3.2.11.1 Main power supply The main supply of the TQMaX4XxL is defined to typ. 5V. By applying the 5V voltage the module generates all required voltages. -
Page 25: Power Sequenzing
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 20 Attention: Malfunction If the absolute maximum voltages of the CPU are exceeded, malfunctions and component failures may occur. The mentioned outputs may not be supplied externally under any circumstances. -
Page 26: Power Consumption
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 21 3.2.11.5 Power consumption The following table lists some technical parameters of the module power supply. The specified current consumption values are to be regarded as reference values. Since the power consumption of the TQMaX4XxL can vary greatly depending on the application, mode and operating system, the values listed here should only be used as a performance estimate. -
Page 27: Pinout Tqmax4Xxl
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 22 3.3.2 Pinout TQMaX4XxL The following table shows the pad-out as top view through the TQMaX4XxL. Table 13: Pinout TQMaX4XxL, top view through TQMaX4XxL SE_ISO SE_ISO MCU_ MCU_... - Page 28 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 23 3.3.2 Pinout TQMaX4XxL (continued) Table 14: TQMaX4XxL pad description Module Voltage Signal Group Description Ball Level Module Main Power supply B1, C1, C2, Add some blocking capacitors for 5.0 V...
- Page 29 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 24 3.3.2 Pinout TQMaX4XxL (continued) Table 32: TQMaX4XxL pad description (continued) RTC Interrupt, Open-Drain. Pullup 1.8 V / RTC_INT# required (typ. 10kΩ) 3.3V RTC_CLK_OUT RTC Clock Output 1.8 V Programmable Alert Output, Open- 1.8 V /...
- Page 30 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 25 3.3.2 Pinout TQMaX4XxL (continued) Table 32: TQMaX4XxL pad description (continued) UART1_RXD UART1_TXD UART1_CTS# UART1_RTS# AA17 MCAN0_RX AB17 MCAN0_TX MCAN1_RX AA16 MCAN1_TX I2C0_SCL I2C0_SDA I2C1_SCL I2C1_SDA OSPI0_CS1# OSPI0_CS2#...
- Page 31 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 26 3.3.2 Pinout TQMaX4XxL (continued) Table 32: TQMaX4XxL pad description (continued) PRG0_MDIO0_MDC PRG0_MDIO0_MDIO PRG0_PRU0_GPO0 PRG0_PRU0_GPO1 PRG0_PRU0_GPO2 PRG0_PRU0_GPO3 PRG0_PRU0_GPO4 PRG0_PRU0_GPO5 PRG0_PRU0_GPO6 PRG0_PRU0_GPO7 PRG0_PRU0_GPO8 PRG0_PRU0_GPO9 PRG0_PRU0_GPO10 PRG0_PRU0_GPO11 PRG0_PRU0_GPO12 PRG0_PRU0_GPO13 PRG0_PRU0_GPO14...
- Page 32 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 27 3.3.2 Pinout TQMaX4XxL (continued) Table 32: TQMaX4XxL pad description (continued) PRG1_PRU0_GPO15 PRG1_PRU0_GPO16 PRG1_PRU0_GPO17 PRG1_PRU0_GPO18 PRG1_PRU0_GPO19 PRG1_PRU1_GPO0 PRG1_PRU1_GPO1 PRG1_PRU1_GPO2 AA12 PRG1_PRU1_GPO3 PRG1_PRU1_GPO4 PRG1_PRU1_GPO5 AA13 PRG1_PRU1_GPO6 PRG1_PRU1_GPO7 PRG1_PRU1_GPO8 PRG1_PRU1_GPO9...
-
Page 33: Software
Multiplexing • Clocks • Driver strengths If a different bootloader is used, these data must be adapted. Details can be requested from TQ support. Further information can be found in the Support Wiki for the TQMaX4XxL. MECHANICS TQMaX4XxL dimensions and footprint The overall dimensions (length ×... - Page 34 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 29 Figure 19: TQMaX4XxL side view Figure 20: Recommended PCB land pattern for TQMaX4XxL, top view through TQMaX4XxL...
-
Page 35: Tqmax4Xxl Component Placement
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 30 TQMaX4XxL component placement Figure 21: TQMaX4XxL component placement top Figure 22: TQMaX4XxL component placement bottom The labels on the TQMaX4XxL show the following information: Table 15: Labels on TQMaX4XxL... -
Page 36: Structural Requirements
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 31 Structural requirements The TQMaX4XxL has to be soldered on the carrier board. The TQMaX4XxL is held on the mainboard by the holding force of the solder connections from the LGA pads and requires no further fastening measures. If there are high requirements for vibration and shock resistance, a module holder must be provided in the final application to additionally hold the module in position. -
Page 37: Safety Requirements And Protective Regulations
TQ. TQ is not liable for any delivery delays due to national or international export restrictions or for the inability to make a delivery as... -
Page 38: Warranty
U.S. Export Administration Regulations in case of US products (ECCN according to the U.S. Commerce Control List) are stated on TQ´s invoices or can be requested at any time. Also listed is the Commodity code (HS) in accordance with the current commodity classification for foreign trade statistics as well as the country of origin of the goods requested/ordered. -
Page 39: Eup
Californians about exposure to Proposition 65 Substances. The TQ device or product is not designed or manufactured or distributed as consumer product or for any contact with end- consumers. Consumer products are defined as products intended for a consumer's personal use, consumption, or enjoyment. -
Page 40: Appendix
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 35 APPENDIX Acronyms and definitions The following acronyms and abbreviations are used in this document: Table 17: Acronyms Acronym Meaning Analog/Digital Converter Analog In Advanced RISC Machine ®... - Page 41 User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 36 Acronyms and definitions (continued) Table 43: Acronyms (continued) Acronym Meaning n.a. Not Available Not Connected Printed Circuit Board PCMCIA People Can’t Memorize Computer Industry Acronyms Pull-Down Physical (layer of the OSI model)
-
Page 42: References
User's Manual l TQMaX4XxL UM 0100 l © 2024, TQ-Systems GmbH Page 37 References Table 18: Further applicable documents Name Rev. / Date Company AM64x Sitara Processors Datasheet A / June 2021 Texas Instruments AM243x Sitara Microcontrollers Datasheet A / June 2021... - Page 43 TQ-Systems GmbH Mühlstraße 2 l Gut Delling l 82229 Seefeld Info@TQ-Group TQ-Group...
Need help?
Do you have a question about the TQMa64xxL and is the answer not in the manual?
Questions and answers