1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Multiplexer
  5. Hotwire 8777
  6. Installation instructions manual

Paradyne Hotwire 8777 Installation Instructions Manual

Tdm sdsl termination units
Hide thumbs Also See for Hotwire 8777:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
®
Hotwire
TDM SDSL Termination Units
Models 8777 and 8779

Installation Instructions

Document Number 8700-A2-GN10-40
March 2003

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com.
Select Support
Select the following document:
To order a paper copy of a Paradyne document, or to speak with a sales
representative, please call 1-727-530-2000.
Hotwire TDM SDSL Termination Units
Hotwire
eight Time Division Multiplexer Symmetric Digital Subscriber Line (TDM SDSL)
interfaces and eight DSX-1 or G.703 interfaces. When the Hotwire 87xx TDM
SDSL Termination Unit is used in a Hotwire 8610/8810 Digital Subscriber Line
Access Multiplexer (DSLAM) chassis or 8620/8820 GranDSLAM chassis, it
transports up to 2064 Kbps signals over traditional twisted-pair telephone wiring.
8700-A2-GN10-40
Technical Manuals
8700-A2-GB20
Hotwire TDM SDSL Termination Units, Models 8777 and 8779, User's Guide
®
8777 and 8779 Termination Units are circuit card assemblies that contain
Model . . .
Has eight . . .
8777
TDM SDSL ports
8779
TDM SDSL ports
March 2003
Hotwire DSL Systems.
And eight . . .
DSX-1 ports
G.703 ports
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hotwire 8777 and is the answer not in the manual?

Questions and answers

Related Manuals for Paradyne Hotwire 8777

Summary of Contents for Paradyne Hotwire 8777

  • Page 1: Installation Instructions

    Select Support Select the following document: 8700-A2-GB20 Hotwire TDM SDSL Termination Units, Models 8777 and 8779, User’s Guide To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2000. Hotwire TDM SDSL Termination Units ®...

  • Page 2: Installation Overview

    Installation Overview Installation and configuration of the Hotwire 87xx TDM SDSL Termination Unit consists of: Installing the Termination Unit in the DSLAM. Connecting to the DTE. Connecting to a Main Distribution Frame (MDF). Providing initial unit identity information or changing existing identity information.
  • Page 3 Installing TDM SDSL Cards A Hotwire TDM SDSL Termination Unit can be installed, removed, and replaced from a DSLAM chassis without disrupting service to the other cards in the chassis. HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation.
  • Page 4 — For a Hotwire 8810 DSLAM or 8820 GranDSLAM chassis – Hold the unit vertically, with the component side facing right, and insert it into the top and bottom card guides. 4. Slide the unit into the slot until the power and network connectors seat firmly in the mating connectors on the backplane.

  • Page 5: Connecting To The Dte

    Connecting to the DTE Connection to the eight DTE ports of the Hotwire 87xx TDM SDSL Termination Unit is through the 50-pin interface connector on its faceplate. Refer to Connector Pin Assignments in the User’s Guide. Procedure To connect the Hotwire 87xx TDM SDSL Termination Unit to your DTE: 1.

  • Page 6: Front Panel Leds

    Front Panel LEDs The following table describes the meaning and states of the LEDs on the Hotwire 8777 or 8779 TDM SDSL Termination Unit’s front panel. PORTS LEDs represent the DTE or DSL ports depending on the Port LEDs selection on the Control screen.

  • Page 7: Logging In To The Hotwire Dslam

    Logging In to the Hotwire DSLAM You can log in to the Hotwire DSLAM system using either a local VT100-compatible terminal or a remote Telnet connection. After you enter your user ID and password, the system displays the Hotwire Chassis Main Menu. See your DSLAM Management Communications Controller (MCC) card documentation for information about selecting the unit from the MCC card selection screen.

  • Page 8: Entering Identity Information

    Entering Identity Information After accessing your unit for the first time, use the Change Identity screen to determine SNMP administrative system information that will be displayed on the Identity screen of the Status branch. To access the Card Identity screen, follow this menu selection sequence: Main Menu Configuring the Unit...

  • Page 9: Configuration Edit/Display

    Inband Management Channel Options March 2003 To Configure the . . . DSL interface ports. DSX-1 interface ports (Model 8777). G.703 interface ports (Model 8779). DSL network and DTE interface ports by copying options from port to port. General system options of the unit.
  • Page 10 Configuring Cross-Connections The Hotwire cross-connect system allows you to connect the DSX-1 or G.703 ports to the DSL ports in a variety of ways: DS1 Bypass mode – The entire DSX-1 or G.703 interface is connected to the DSL interface. DS1 Cross-Connect mode –...

  • Page 11: Important Safety Instructions

    Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.

  • Page 12: Warranty, Sales, Service, And Training Information

    The authority to operate this equipment is conditioned by the requirements that no modifications will be made to the equipment unless the changes or modifications are expressly approved by Paradyne Corporation. CANADA – EMI NOTICE: This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.

This manual is also suitable for:

Hotwire 8779

Table of Contents