Subscribe to Our Youtube Channel
Related Manuals for Ross openGear FSS-6800 Series
Summary of Contents for Ross openGear FSS-6800 Series
- Page 1 Ross Video Limited FSS-6800 and FDS-6800 Series Passive Optical Splitters User Manual...
- Page 2 The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed as commitment by Ross Video Limited. Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.
- Page 3 Important Regulatory and Safety Notices Before using this product and any associated equipment, refer to the “Important Safety Instructions” listed below to avoid personnel injury and to prevent product damage. Products may require specific equipment, and/or installation procedures to be carried out to satisfy certain regulatory compliance requirements.
- Page 4 Notice — Changes or modifications to this equipment not expressly approved by Ross Video Limited could void the user’s authority to operate this equipment. CANADA This Class “A” digital apparatus complies with Canadian ICES-003.
- Page 5 Important Laser Safety Measures and Notices Before using this product and any associated equipment, refer to the sections below so as to avoid personnel injury and to prevent product damage. For further safety information when using fiber products, consult the following publications: •...
- Page 6 The crossed-out wheeled bin symbol invites you to use these systems. If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration. You can also contact Ross Video for more information on the environmental performances of our products.
- Page 7 Company Address Ross Video Limited Ross Video Incorporated 8 John Street P.O. Box 880 Iroquois, Ontario Ogdensburg, New York Canada, K0E 1K0 USA 13669-0880 General Business Office: (+1) 613 • 652 • 4886 Fax: (+1) 613 • 652 • 4425 Technical Support: (+1) 613 •...
-
Page 9: Table Of Contents
Contents Introduction Overview..........................1-2 Features........................1-2 Functional Block Diagrams ....................1-3 Documentation Terms and Conventions................1-5 Installation Before You Begin ........................ 2-2 Unpacking......................2-2 Working with Fiber Optic Connectors ..............2-2 Installing a Passive Optical Splitter ..................2-3 Rear Modules for the Passive Optical Splitters............. 2-3 Installing a Rear Module .................. - Page 10 ii • Contents FSS-6800 and FDS-6800 Series User Manual (Iss. 01)
-
Page 11: Introduction
Congratulations on choosing an openGear FSS-6800 and FDS-6800 series Passive Optical Splitters. Your FSS-6800 and FDS-6800 series are part of a full line of Digital Products within the openGear Terminal Equipment family of products, backed by Ross Video's experience in engineering and design expertise since 1974. -
Page 12: Overview
Overview The FSS-6800 and FDS-6800 series are passive optical splitters, using Planar Lightwave Circuit (PLC) technology, that takes in an input signal and splits it into several output signals. The FSS-6800 and FDS-6800 series is an implementation of CWDM takes an optical signal and splits it to two or more outputs but while using no electrical power. -
Page 13: Functional Block Diagrams
Functional Block Diagrams This section provides the workflow diagrams for the FSS-6800 and FDS-6800 series. Figure 1.1 FSS-6802 — Simplified Block Diagram Figure 1.2 FDS-6803 — Simplified Block Diagram Figure 1.3 FSS-6804 — Simplified Block Diagram FSS-6800 and FDS-6800 Series User Manual (Iss. 01) Introduction •... - Page 14 Figure 1.4 FDS-6805 — Simplified Block Diagram Figure 1.5 FSS-6808 — Simplified Block Diagram 1–4 • Introduction FSS-6800 and FDS-6800 Series User Manual (Iss. 01)
-
Page 15: Documentation Terms And Conventions
Documentation Terms and Conventions The following terms and conventions are used throughout this manual: • “Frame” refers to DFR-8321 series frame that houses the FSS-6800 and FDS-6800 series, as well as any openGear frames. • All references to the DFR-8321 series frame also includes all versions of the DFR-8321 frames and any available options unless otherwise noted. - Page 16 1–6 • Introduction FSS-6800 and FDS-6800 Series User Manual (Iss. 01)
-
Page 17: Installation
Installation In This Chapter This chapter provides instructions for installing the FSS-6800 and FDS-6800 series into the frame, and cabling details. When installed, the modules are not visible through DashBoard nor SNMP and there are no card-edge controls. The following topics are discussed: •... -
Page 18: Before You Begin
DFR-8300 Series User Manual. Unpacking Unpack each Passive Optical Splitter you received from the shipping container and ensure that all items are included. If any items are missing or damaged, contact your sales representative or Ross Video directly. Working with Fiber Optic Connectors Keep the following in mind when working with fiber optic connectors: •... -
Page 19: Installing A Passive Optical Splitter
Installing a Passive Optical Splitter An installed Passive Optical Splitter blocks the card slots in the frame so that the modules are not damaged if a user attempts to slide a card into the slot occupied by the Passive Optical Splitter. This section outlines how to install a rear module, and then the Passive Optical Splitter in a DFR-8321 series frame. -
Page 20: Removing A Passive Optical Splitter
Installing a Passive Optical Splitter All the components are enclosed in a metal box that fits into the frame card guides. The Passive Optical Splitters latch to the rear module to prevent accidental removal when the fiber optic cables are installed. This section outlines how to install a Passive Optical Splitter in a DFR-8321 series frame. -
Page 21: Cabling For The Passive Optical Splitters
Cabling for the Passive Optical Splitters This section provides information for connecting cables to the installed Passive Optical Splitter. Connect the input and output cables according to the following sections. Notice — Every time you are required to insert a connector into a device or mating sleeve, you must clean the connector. -
Page 22: Installing And Removing Fiber Optic Cables
The limited space between connectors and the accumulated fiber optic cables around the rear modules makes it difficult to gain access to individual connectors. Ross Video supplies an Optic Cable Tool to assist in the installing and removal of individual fiber optic LC connectors. The Optic Cable Tool can be used with single-latch, dual-latch, and duplex-latch connectors. - Page 23 Removing a Fiber Optic Cable Use the following procedure to remove a fiber optic cable using the Optic Cable Tool: 1. Position the bottom lip of the Optic Cable Tool on the connector boot, ensuring that the top lip makes contact just behind the notch at the end of the latch. (Figure 2.8) Figure 2.8 Positioning the Optic Cable Tool —...
- Page 24 2–8 • Installation FSS-6800 and FDS-6800 Series User Manual (Iss. 01)
-
Page 25: Specifications
Specifications In This Chapter This chapter includes the technical specifications for the Passive Optical Splitters. Note that specifications are subject to change without notice. The following topics are discussed: • FSS-6800 Series Technical Specifications • FDS-6800 Series Technical Specifications FSS-6800 and FDS-6800 Series User Manual (Iss. 01) Specifications •... -
Page 26: Fss-6800 Series Technical Specifications
FSS-6800 Series Technical Specifications This section provides the technical specifications for the FSS-6800 series. Table 3.1 FSS-6800 Series Technical Specifications Category Parameter Specification Supported Wavelengths 1260nm to 1650nm Return Loss minimum 50dB FSS-6802: 4dB Maximum Insertion Loss FSS-6804: 8dB FSS-6808: 11dB FSS-6802: 0.4dB Optical Uniformity... -
Page 27: Fds-6800 Series Technical Specifications
FDS-6800 Series Technical Specifications This section provides the technical specifications for the FDS-6800 Series. Table 3.2 FSS-6800 Series Technical Specifications Category Parameter Specification Supported Wavelengths 1260nm to 1650nm Return Loss minimum 50dB FDS-6803: 4dB Maximum Insertion Loss FDS-6805: 8dB Optical FDS-6803: 0.4dB Input/Output Uniformity... - Page 28 3–4 • Specifications FSS-6800 and FDS-6800 Series User Manual (Iss. 01)
-
Page 29: Service Information
Service Information In This Chapter This chapter contains the following sections: • Troubleshooting Checklist • Warranty and Repair Policy FSS-6800 and FDS-6800 Series User Manual (Iss. 01) Service Information • 4–1... -
Page 30: Troubleshooting Checklist
Troubleshooting Checklist Routine maintenance to this openGear product is not required. In the event of problems with your Passive Optical Splitters, the following basic troubleshooting checklist may help identify the source of the problem. If the frame still does not appear to be working properly after checking all possible causes, please contact your openGear products distributor, or the Technical Support department at the numbers listed under the “Contact Us”... -
Page 31: Warranty And Repair Policy
In the event that your FSS-6800 and FDS-6800 series proves to be defective in any way during this warranty period, Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics. - Page 32 P.O. Box 880, Ross Video Incorporated Ogdensburg, New York, USA 13669-0880 Visit Us Please visit us at our website for: • Company information • Related products and full product lines • On-line catalog • News • Testimonials Ross Part Number: 6802DR-004-01...
Need help?
Do you have a question about the openGear FSS-6800 Series and is the answer not in the manual?
Questions and answers