Paradyne 3821Plus Quick Reference Manual page 18

AT COMMANDS (continued)
+FCLASS=n Fax class
+FCLASS=0 Data
+FCLASS=1 Fax Class 1 (EIA 578)
+FCLASS=2 Fax Class 2 (EIA/TIA SP-2388)
&&P1 Clone Remote
&&P1 Copies firmware to the connected
modem.
&Cn LSD Control
&C0 Forced On. Forces LSD ON at all times.
&C1 Standard RS232. LSD is ON when the
remote modem's carrier signal is
detected. LSD is Off when carrier
signal is not detected.
&C2 Wink When Disc. LSD, normally forced
ON, turns Off for approximately 1 to 2
seconds upon disconnect.
&C3 Follows DTR. State of LSD follows state
of DTR.
&C4 Simulated Control Carrier. State of LSD
follows state of remote modem's RTS.
&C5 =DTR/DiscOff. State of LSD follows
state of DTR except upon a disconnect
where DTR remains ON and LSD turns
Off. DTR must then toggle Off and ON to
turn LSD ON. Required for AT&T
DATAKIT dial-out applications.
&Dn DTR Action
&D0 Ignore. Modem ignores the DTR (Data
Terminal Ready) signal and treats it as
always ON.
&D1 Off=Command Mode. Modem enters
online Command mode when DTR is
lowered.
&D2 Standard RS232. DTR signal is
controlled by the DTE.
&D3 Off=Reload Straps. Modem loads Active
(Operating) area with Active (Saved)
area when DTR is lowered.
&D4 Controls On-Hook. Modem does not
disconnect until DTR lowered by DTE.
&D6 Off=Restrap to Async Dial. Modem loads
Async Dial template when DTR switches
off.
&Fn Loads Factory Configuration
&F0 Loads the Async Dial template into the
Active(Operating) area.
&F1 Loads Sync Dial.
&F2 Loads Sync Leased (Answer Mode).
&F3 Loads Unix Dial.
&F4 Loads Sync Leased (Originate Mode).
&F5 Loads Cellular (Mobile) (if ETC installed).
&F6 Loads Cellular (PSTN) (if ETC installed).
&Gn V.22bis Guard Tone
&G0 Disables guard tone.
&G1 Sets guard tone to 550 Hz.
&G2 Sets guard tone to 1800 Hz.
AT COMMANDS (continued)
& I n Dial Transmit Level
& I 10 –10 dBm.
I
& 11 –11 dBm.
& I 32 –32 dBm.
& I 99 ETC 1.0 (if ETC installed).
I
& 100 ETC 1.1 (if ETC installed).
&Jn Dial Transmit Level Type
&J0 Modem sets dial transmit level to
Permissive mode at –9 dBm.
&Ln Leased-Line Mode
&L0 Disables leased-line operation.
&L1 2-wire originate leased-line operation.
&L3 2-wire answer leased-line operation.
&Mn,&Qn Async/Sync Mode and DTE Dialer Type
&M0,&Q0 Modem operates in Async mode and
uses AT command protocol.
&M1,&Q1 Modem operates in Sync mode and uses
AT command protocol.
&M2,&Q2 Modem operates in Sync mode and dials
the number stored in directory location 1
when DTR signal turns Off and then ON.
&M3,&Q3 Modem operates in Sync mode and uses
AT command protocol.
&M231, &Q231 Modem operates in Async mode;
the DTE Dialer Type is disabled.
&M232, &Q232 Modem operates in Async mode;
V.25bis Async dialing is enabled.
&M233, &Q233 Modem operates in Sync mode;
V.25 Bisync dialing is enabled.
&M234, &Q234 Modem operates in Sync mode;
V.25bis HDLC dialing is enabled.
&Rn RTS Action
&R0 Standard RS232. RTS action is
controlled by DTE.
&R1 Ignores RTS. Modem ignores RTS
signal and treats it as always ON.
&R2 Simulated Control Carrier. State of RTS
follows state of LSD.
&Sn DSR Control
&S0 Forced On. Forces DSR signal ON.
&S1 Standard RS232. Modem controls DSR
signal.
&S2 Wink When Disc. DSR signal turns Off
for approximately 1 to 2 seconds upon
disconnecting.
&S3 Follows DTR. Modem sends DSR to DTE
when it receives DTR from DTE.
&S4 On Early. DSR is Off when modem is in
idle state. DSR goes ON when modem
enters Data mode.
&S5 Delay to Data. DSR does not turn ON
until the modem enters Data mode.
16