Model 2 network diagnostic modems point-to-point sna diagnostic interface with dbm-v option supplement (178 pages)
Summary of Contents for Paradyne COMSPHERE 3811Plus
Page 1
AREA CODE CHANGE Please note that the area code for Paradyne Corporation in Largo, Florida has changed from 813 to 727. For any Paradyne telephone number that appears in this manual with an 813 area code, dial 727 instead.
FCC registration number and ringer equivalence number (REN) for this equipment. The label is located on the circuit card assembly of the 3811Plus. If requested, this information must be provided to the telephone company. 2. The Universal Service Order Code (USOC) for Permissive mode is RJ21X.
Page 3
RENs, contact the telephone company to determine the maximum RENs for the calling area. 4. If the 3811Plus modem causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if...
Page 4
The Load Number for this equipment is on the label on the modem. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading.
— Within the U.S.A., call 1-800-870-2221 — International, call 813-530-2340 Installation Customer-Supplied Equipment The 3811Plus modem (see Figure 1) is designed for installation in a COMSPHERE 3000 Series Carrier which supplies operating power and the dial-line and/or leased-line network connections. For power, dial-line,...
Page 6
Status Alrm Test Dial Busy Serv Front Panel Spkr 3811 Plus 3980-A2-GZ41-10 EIA232/V.24 Faceplate Connector EIA232/V.24 Edge Card Connector Figure 1. 3811 Plus Modem November 1996 Rear Connector Plate Unused 496-14488-02...
Page 7
SDCP. The SDCP of the COMSPHERE 3000 Series Carrier is the user interface to the 3811Plus modem. A single SDCP can control modems in up to eight carriers. To install a 3811Plus modem into the carrier, perform the following steps.
Page 8
Open (Unlocked) Latch 4. If the carrier is connected to power, the Power LED on the faceplate of the 3811Plus lights up. After several seconds the modem completes its power-up self-test in which all faceplate LEDs light up. If the modem fails, or an alarm condition exists, the Alrm LED on the faceplate lights up or flashes.
After the modem passes the power-up self-test, configure it for operation using one of the factory preset configurations. The 3811Plus modem has several factory preset templates that contain the proper configuration options (straps) for different environments. Modems are shipped from the factory with the Async Dial default configuration options stored in memory.
To change a factory template using AT commands, perform the following steps. Procedure 1. Enter the appropriate factory configuration command (&Fn) followed by the &W0 command to store the configuration in Active (Saved) and the Z command to reset the modem. TYPE: AT&Fn&W0Z Where: n is one of the following Factory configurations:...
Page 11
Call_Setup Dial Answer Change_Directory Disconnect Dial_Standby Return_to_Dial Directory Locations 1 – 10 Does not appear in Remote Mode. (Rem_Digital_Loop, Loc_Digital_Loop, and Pattern appear if the secondary channel is used.) Some choices within this group may not appear depending upon how previous configuration options have been selected.
Page 12
from previous page Activ (Operating) Active (Saved) from previous page Leased_Line V42/MNP/Buffer Leased Mode Err Contrl Mode Modulation V42bis Compress LeasedLine Rate MNP5 Compress Autorate EC Negotiat Bfr Leased TX Level EC Fallbck Char Bad Ln Auto Orig Flw Cntl of DTE Rate Auto Orig Flw Cntl of Mdm Auto Redial...
Page 13
from previous page Control Remote Security Secondary Prim (data blckd) (ExitRem appears instead of Remote when using Remote Mode) Set_Access_Ctrl Reset_Security (Admin Password?) EditPassWdTable Set_Orig_Secur Set_Answer_Sec Set_Admin_PsWd Speaker Make_Busy Download Code RemoveMakeBusy Reset Service_Line Install DiscServLine Does not appear in Remote Mode. (Rem_Digital_Loop, Loc_Digital_Loop, and Pattern appear if the secondary channel is used.)