Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Multiplexer
  5. 9161 Single T1
  6. Quick reference

Paradyne 9161 Quick Reference

Zhone 9161 mux: quick reference
Hide thumbs Also See for 9161:

Advertisement

Quick Links

Download this manual See also: Reference Manual, User Manual
916x/926x T1 Access Mux
Quick Reference
Document Number 9161-A2-GL10-10
December 1998
Product Documentation on the World Wide Web
We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the waste of
surplus printing. It also helps us maintain competitive prices for our products.
Complete documentation for this product is available at www.paradyne.com.
Select Service & Support
Select the following document:
9161-A2-GH30
Model 916x/926x T1 Access Mux Technical Reference
To request a paper copy of a Paradyne document:
H
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
H
Outside the U.S.A., call 1-727-530-8623
Overview
This quick reference summarizes the configuration options accessed when you select
Configuration from the Main Menu. Not all options are available, but are filtered
depending on what other options have been selected. Refer to Chapter 5, Setting Up ,
in the Model 916x/926x T1 Access Mux Technical Reference for more information.
TM
Technical Manuals
1
T1 Access Multiplexers.

Advertisement

loading

Related Manuals for Paradyne 9161

Summary of Contents for Paradyne 9161

  • Page 1 916x/926x T1 Access Mux Quick Reference Document Number 9161-A2-GL10-10 December 1998 Product Documentation on the World Wide Web We provide complete product documentation online. This lets you search the documentation for specific topics and print only what you need, reducing the waste of surplus printing.

  • Page 2: Menu Hierarchy

    Menu MAIN MENU Hierarchy Status Test Configuration Control Network Channel Display Network DSX-1 Channel Display Sync Data Ports Port Assignment Display Clear Statistics MAIN MENU Status Test Configuration Control DSX-1 to Network Communication Port Assignments External Device (Com Port) Network to Network Assignments Telnet/FTP Sessions Voice Port...
  • Page 3 Network Configuration Option Network Interface Status Line Framing Format Line Coding Format Line Build Out (LBO) Bit Stuffing Network Initiated LLB Network Initiated PLB Transmit Timing ANSI Performance Report Messages Management Link IP Address Subnet Mask Routing Information Protocol Network Time Slot Circuit Identifier Loss of Signal (LOS) Alarm Out of Frame (OOF) Alarm...
  • Page 4 DSX-1 Configuration Option Slot ss Port p Interface Status Line Framing Format Line Coding Format Line Equalization Send All Ones on DSX-1 Failure Loss of Signal (LOS) Alarm Out of Frame (OOF) Alarm Alarm Indication Signal (AIS) Yellow Alarm Settings 916x: 01 9261 NAM: 02 9265: 02, 03, 04, 05...
  • Page 5 Sync Data Ports Configuration Option Slot ss Port p Port Status Port Type Port Base Rate Transmit Clock Source Invert Transmit Clock Invert Transmit and Received Data Send All Ones on Data Port Not Ready Action on Network Yellow Alarm Network Initiated Data Channel Loopback (DCLB) Port (DTE) Initiated Loopbacks...
  • Page 6 Voice Ports Configuration Option E&M Voice Slot ss Port p Port Status Operating Mode Rx Gain (dB) Tx Attenuation (dB) Trunk Cond in CGA FXO Voice Slot ss Port p Port Status Operating Mode Signaling Type Terminating Impedance (ohms) Wink Delay (10 ms) Wink Duration (10 ms) Rx Gain (dB) Tx Attenuation (dB)
  • Page 7 Voice Ports (continued) FXS Voice Slot ss Port p Port Status Operating Mode Signaling Type Terminating Impedance (ohms) Wink Delay (10 ms) Wink Duration (10 ms) Rx Gain (dB) Tx Attenuation (dB) Ring-Back Tone Trunk Cond in CGA 9x62: 02 9x65: 02, 03, 04, 05 1, 2, 3, 4, 5, 6, 7, 8 Enable, [Disable]...
  • Page 8 OCU-DP Ports Configuration Option Slot ss Port p Port Status Port Rate Loopback Detection Loss of Signal Alarm Abnormal Station Code Alarm 64KCC Loop OOF Alarm DDS Network Failure Alarm Loss of Loop Timing Alarm Settings 9x62: 02 9x65: 02, 03, 04, 05 2-port: 1, 2 6-port: 1, 2, 3, 4, 5, 6 Enable, [Disable]...

  • Page 9: Cross Connect

    Cross Connect See the Technical Reference for information on cross connections. Copy Ports Configuration Option From: Slot ss From: Port p Type To: Slot ss To: Port p Perform Copy Perform Copy Then Increment Settings 9x62: 01, 02 9x65: 01, 02, 03, 04, 05 T1 NAM: 1, 2 Sync Data APM: 1, 2, 3, 4 Voice APM: 1, 2, 3, 4, 5, 6, 7, 8...
  • Page 10 System Options Configuration Option Generate Yellow Alarm Signals Test Timeout Test Duration (min) Primary Clock Source Port (for Primary Clock Source) Secondary Clock Source Port (for Secondary Clock Source) S ss P p External Clock Rate (KHz) Primary Clock Failure Alarm Secondary Clock Failure Alarm Settings [Enable], Disable...
  • Page 11 User Interface Configuration Option Communication Port Physical characteristics of the Port ( Port 1 or 2) Port Use Port Type Port Type – Synchronous Clock Source Data Rate (Kbps) Port Type – Asynchronous Data Rate (Kbps) Character Length Parity Stop Bits Ignore Control Leads Login Required Port Access Level...
  • Page 12 User Interface (continued) Configuration Option External Device (COM Port) External Device Commands Dial-In Access Connect Prefix Connect Indication String Escape Sequence Escape Sequence Delay (Sec) Disconnect String Telnet/FTP Sessions Telnet Session Telnet Login Required Session Access Level Inactivity Timeout Disconnect Time (Minutes) FTP Session FTP Login Required Only shown when External Device Commands is set to Other or AT.
  • Page 13 Management and Communications Configuration Option Communication Protocol Node IP Address Node Subnet Mask Default Network Destination Communication Port IP Address Communication Port Subnet Mask [000.000.000.000] – 255.255.255.255, Clear Communication Port Link Protocol [PPP], SLIP Alternate Communication Port IP Address Alternate Communication Port Subnet Mask General SNMP Management SNMP Management...
  • Page 14 Management and Communications (continued) SNMP Traps SNMP Traps Number of Trap Managers NMS n IP Address Destination General Traps Enterprise Specific Traps Link Traps Link Traps Interfaces The first byte cannot be set to 0 nor 127. However, the null address of 0.0.0.0 is valid after performing a Clear.

  • Page 15: Document Feedback

    Warranty, Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Via the Internet: Visit the Paradyne World Wide Web site at http://www.paradyne.com Via Telephone: Call our automated call system to receive current information via...

This manual is also suitable for:

9261