Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MSI EV Series
- Page 1 EV Series EV Charging EV Life EV Life Plus EV Premium EV AI User Guide...
-
Page 2: Table Of Contents
Contents Safety Information ......................3 Accessories ........................5 Introduction ........................6 Product Overview ....................6 Installation ........................7 Site Requirements ....................7 Installation Overview ....................7 Installation Steps ....................8 Initial Startup ......................16 Verification ......................17 Operation ........................18 Charging Procedures ................... -
Page 3: Safety Information
Safety Information ⚠ Please read and follow these safety instructions carefully before installing, operating or performing maintenance on the EVSE. Risk of electric shock Dangerous voltages and currents can occur during operation of the EVSE. Therefore, before carrying out any work on the EVSE, take the following protective measures: ∙... - Page 4 Warning notices and symbols Do not remove any warning notices, warning symbols, or other markings attached to the EVSE by MSI. Duty of supervision As the operator of the EVSE, you are responsible for the safety of the users and its proper use.
-
Page 5: Accessories
Accessories Item Name / Q’ty Used for Mounting the EVSE Wall mount bracket securely on a wall or suitable surface M6 step screws Securing on the back of the EVSE M6 waterproof screws Securing the EVSE onto the wall mount bracket M3*8 screws Assembling the bottom cover of the EVSE... -
Page 6: Introduction
Introduction Thank you for choosing the MSI EV charger. This EVSE is a reliable and efficient charging solution designed to meet the needs of electric vehicle owners. With its user-friendly interface and compact size, it is easy to install and operate, making it an ideal choice for both residential and commercial use. -
Page 7: Installation
Installation Before installing the EVSE, please ensure that the installation site meets the following requirements. Site Requirements ∙ The installation site should be dry, well-ventilated, and free from direct exposure to sunlight. ∙ The installation site should have a flat and stable surface that can support the weight of the EVSE. -
Page 8: Installation Steps
Installation Steps 1. Choose a suitable location and ensure it is a masonry wall. Determine the installation position of the EVSE and mark the top two holes and the bottom two holes on the wall for drilling in alignment with the wall mount bracket. 2. - Page 9 3. Insert four 3/8’’-1/2’’ expansion bolts into the drilled holes. Ensure the bolts are fully inserted. (Note: Expansion bolts are not included and must be purchased separately.) Expansion Bolt Information: Bolt diameter (d): 3/8’’ Outer diameter of anchor (D): 1/2” Anchor length (A): 60 mm (2.36 inches or 2 3/8”) 4.
- Page 10 5. Align the wall mount bracket with the expansion bolts. Place the bracket onto the wall, ensuring that the bolts align with the corresponding holes on the bracket. Install washers and nuts on each of the four expansion bolts. Tighten the nuts to a torque of 10.9Nm to securely attach the bracket to the wall.
- Page 11 7. Remove the 4 screws that secure the plastic cover or camera module. Then, remove the plastic cover or camera module accordingly. 8. Install 4 M6 step screws (included in the screw bag) on the back of the EVSE.
- Page 12 9. Hang the EVSE onto the wall mount bracket. 10. Use 2 M6 waterproof screws (included in the screw bag) to secure the EVSE onto the wall mount bracket.
- Page 13 11. Insert the AC input power cable with the appropriate amperage rating through the bottom entry of the EVSE. Connect it to the L1, L2/N, and Ground terminals using UL-approved and insulated ring terminals. For the connections to L1 and L2/N, use M6 ring terminals with an inner diameter of 6.4 mm.
- Page 14 12. There are optional components located above the screw terminal blocks. Please follow the instructions below: Internal testing Normal (Default) A. LAN Port (Optional): EV Life Plus, EV Premium and EV AI offer an optional LAN port for wired connection if required. B.
- Page 15 13. For EV AI only, adjust the camera module as needed. To adjust the angle of the camera, locate the positioning screw on the camera turntable and loosen it. Then, rotate the camera to the desired position and tighten the screw to secure it in place.
-
Page 16: Initial Startup
Initial Startup After the installation is complete, follow the steps below to start up the EVSE: 1. Ensure the EVSE is properly installed and securely mounted. 2. Confirm that the emergency stop button is in the released position. If not, rotate once to release. -
Page 17: Verification
Verification After completing the installation and initial startup, it is important to verify that the EVSE is functioning properly. Follow the steps below to perform a verification check: 1. Connect an electric vehicle to the EVSE and ensure that it is properly connected and charging. -
Page 18: Operation
Operation After the initial setup and verification, the EVSE is ready to use. To operate the EVSE, follow the steps below: 1. Connect your electric vehicle to the EVSE. 2. If you have an LCD display model, the screen will display the charging progress and any relevant information. -
Page 19: Troubleshooting
Troubleshooting In the event of a problem or issue with the EVSE, refer to the troubleshooting guide below: The EVSE does not start charging the EV. ∙ Check the connection between the EV and the EVSE. Ensure that the EV charging connector is properly plugged into the charging port of the EV. - Page 20 Error Code: 4 LED Indicator: ○○○●● (3 off, 2 on) Cause: GFCI Fault 2 Solution: Check if the power and GC cable of the EVSE are properly connected. Contact a qualified electrician in your area to check the power environment. Error Code: 5 LED Indicator: ●●○○○...
- Page 21 Error Code: 22 LED Indicator: ○●●●● (1 off, 4 on) Cause: Overcurrent Failure Solution: Check/measure the source current for correctness. Error Code: 24 LED Indicator: ●●●●○ (4 on, 1 off) Cause: Overvoltage Solution: Check/measure the source voltage for correctness. Error Code: 25 LED Indicator: ●●●●○...
- Page 22 Error Code: 64 LED Indicator: ●●●●● (5 on) Cause: Pile Fault Solution: Restart Error Code: InstallationFailed LED Indicator: ●●●●● (5 on) Cause: Installation Failed Solution: Contact Customer Support...
-
Page 23: Maintenance
Maintenance Proper maintenance can help ensure the longevity and optimal performance of the charging station. Here are some general maintenance guidelines to follow: General Maintenance ∙ Regularly inspect the charging station for any visible damage or signs of wear and tear. -
Page 24: Specification
Specification Comparison of Key Differences Marketing Name EV Life EV Life Plus EV Premium EV AI Weight (Without charging 6.5 kg 6.9 kg 7 kg 7.1 kg connector*) Mobile App, User RFID (ISO/ Mobile App, QR Code, RFID Mobile App Authentication IEC 14443-A, (ISO/IEC 14443-A, MIFARE) - Page 25 Protection ∙ IEC regulation requires external and certified RCDs ∙ Suggested specification is Type B ∙ UL regulations do not require the use of an external RCD. Randomized delay before charge resume after Cold-Load Pickup power failure ∙ Surge Protection ∙...
- Page 26 Environment Operating Temperature -30 ~ 50 ℃ Cooling Natural cooling IP Rating IP55 Humidity < 95% relative humidity, non-condensing Altitude Up to 3,000 m Installation Wall mount / Stand...
-
Page 27: Regulatory Information
Regulatory Information Wireless Radio Use This device is restricted to indoor use when operating in the 2.4GHz, 5GHz, 6GHz frequency band. Cet appareil doit être utilisé à l’intérieur. 당해 무선설비는 운용중 전파혼신 가능성이 있음. この製品は 、 周波数帯域 2.4GHz, 5GHz, 6GHz で動作しているときは 、 屋内においてのみ使 用可能です...