Skil IF5940E-00 - Cordless Dual Function Inflator Manual

INTRODUCTION

• This tool is intended for inflating tires, balls and other small volume items which fit the air chuck directly, or by using the supplied adapters
• This tool is intended for inflating large volume items such as air beds, pools, boats, etc.
• This tool is not intended for professional use
• Read this instruction manual carefully before use and save it for future reference

OVERVIEW

SPECIFICATIONS

USE

• Charging battery
  read the safety warnings and instructions provided with the charger
• Removing/installing the battery
• Battery protection
  
  The tool is suddenly being switched off or prevented from being switched on, when
  • the load is too high → remove load and restart
  • the battery temperature is not within the allowable operating temperature range of -20 to +50°C → 2 levels of the battery level indicator start flashing when pressing button c; wait until battery has returned within the allowable operating temperature range.
  • the battery is nearly empty (to protect against deep discharge) → a low battery level or flashing low battery level b is shown by the battery level indicator when pressing button; charge battery
    do not continue to press the on/off switch after the tool is switched off automatically;
    battery may be damaged
• Car socket connection
  
  • as alternative to a battery pack, the car socket can be used as power supply.
  • remove the car socket adapter from the storage compartment.
  • connect adapter to the car socket
• On/off
  • press button
  • LCD display will show pressure information
  • by pressing the function button you can switch between high pressure (default) and high volume function
  • press LED button to turn the work light on/off
  • press button again to turn off
    after approx. 5 minutes of inactivity the tool will automatically turn off

HIGH PRESSURE FUNCTION

• Connecting the air hose
  
  • unlock the air chuck clamp
  • place the air chuck on valve stem
    for Presta and Dunlop valves screw the adapter on the valve stem before placing the air chuck.
  • push the air chuck down so that the threaded section of the valve stem is inside the air chuck
  • lock the air chuck clamp
• Removing/installing adapters
  
  • unlock the air chuck clamp
  • push the adapter into the air chuck until it stops
  • lock the air chuck clamp
• Set target pressure
  
  make sure that the high pressure function is selected a
  • target pressure can be increased and decreased with + and – buttons to the desired value (between 0.2 and 11.0 bar)
  • to change the pressure unit press + and – buttons together
    to avoid over inflation, read the instruction provided with the items to be inflated and never exceed recommended pressures
• Inflating
  • to start inflating, press start/pause button
  • the actual pressure is shown
    when the actual pressure is higher than the target pressure, the tool will not start inflating
  • to pause or stop inflating, press start/pause button again
  • the tool stops when the target pressure is reached
  • the tool stops when the target pressure is reached
    the actual pressure may drop after the tool has stopped; you may restart inflating until the target pressure is reached
    the tool may stop without reaching the target pressure when a low target pressure is set (< 2 bar); you may restart inflating until the target pressure is reached
    allow the tool to cool down for 5 minutes after each 15 minutes of continuous use

HIGH VOLUME FUNCTION

• Inflating
  • connect the high volume air hose to the air outlet
  • connect the other end of the hose to the item to be inflated directly or with the tapered adapter
    make sure that the high volume function is selected b
  • to start inflating, press button
  • to pause or stop inflating, press button again
    the tool does not stop automatically when high volume function is chosen
    allow the tool to cool down for 5 minutes after each 15 minutes of continuous use
• Deflating
  • for deflating, follow the instruction above, but connect the high volume air hose to the air intake
    

MAINTENANCE

• This tool is not intended for professional use
• Always keep tool clean (especially ventilation slots)
  remove battery from tool before cleaning

SAFETY

• Never allow children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or people unfamiliar with these instructions to use the tool.
• Supervise children(this will ensure that children do not play with the tool)
• Cleaning and user maintenance of the tool shall not be made by children without supervision
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Store the tool indoors in a dry and locked-up place, out of reach of children
• Do not use tool when damaged; take it to one of the officially registered SKIL Service Stations for a safety check
• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Provide for good ventilation at the working place
• Make sure that the hose is free of obstructions or snags. Entangled or snarled hoses may become damaged
• Never leave an inflator unattended with the air hose attached
• Do not continue to use an inflator or hose that leaks air or does not function properly
• Do not attempt to pull or carry the inflator by the hoses Only use the following batteries and chargers with this tool
  • SKIL battery: BY5197E-03 BY5196E-03
  • SKIL charger: SC5358E-01 QC5360E-01 QC5359E-00
• Do not use battery when damaged; it should be replaced immediately
• Do not disassemble the battery
• Do not expose tool/battery to rain
• Permitted ambient temperature (tool/charger/battery):
  • when charging 4...40°C
  • during operation –20...+50°C
  • during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

Read the instruction manual before use

Insulation class III

Do not dispose of electric tools and batteries together with household waste material

For Customer Service
1300-017-545
OR
www.skil.com.au