Xylem Bell & Gossett e-1531 Series Quick Start Manual

Xylem Bell & Gossett e-1531 Series Quick Start Manual

Smart pumps

Advertisement

Quick Links

1 Introduction
NOTICE:
Read the installation, operation and maintenance instructions located
on the Xylem website before use. Improper use of the product can
cause personal injury and damage to property and may void the war‐
ranty. See e-1531/32, hydrovar X Smart Pump, and hydrovar X Instruc‐
tion Manuals for complete product warranty and installation instruc‐
tions.
WARNING:
Personal protective equipment should be worn when
handling this equipment. Only use properly sized certi‐
fied lifting equipment & lifting devices, including slings,
suitably rated for the weights to be lifted. Slings, when
used, must be of identical materials to avoid differences
in stretch rates. Do not use lifting devices that are frayed,
kinked, unmarked, or worn.
2 Lifting and handling requirements
WARNING:
• Assembled units and their components are heavy.
Failure to properly lift and support this equipment
can result in serious physical injury and/or equipment
damage. Lift equipment only at the specifically identi‐
fied lifting points. Lifting devices such as eyebolts,
slings, and spreaders must be rated, selected, and
used for the entire load being lifted.
• Crush hazard. The unit and the components can be
heavy. Use proper lifting methods and wear steel-to‐
ed shoes at all times.
Series e-1531X & e-1532X Smart
Pumps
For safety and correct product usage, read the manual before this
product is used.
WARNING:
Always lock out power to the driver before you perform
any installation of maintenance tasks. Failure to discon‐
nect and lock out driver power will result in serious injury.
WARNING:
This product can expose you to chemicals including
Lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For
more information go to: www.P65Warnings.ca.gov.
QUICK GUIDE
P2006093 Rev B
THE MANUAL IS AVAILABLE AT:
https://qr.xylemsales.com/hijesr

Advertisement

Table of Contents
loading

Summary of Contents for Xylem Bell & Gossett e-1531 Series

  • Page 1 Read the installation, operation and maintenance instructions located any installation of maintenance tasks. Failure to discon‐ on the Xylem website before use. Improper use of the product can nect and lock out driver power will result in serious injury. cause personal injury and damage to property and may void the war‐...
  • Page 2: Unit Installation

    For safety and correct product usage, read the manual before this product is used. 3 Unit Installation 3.1 Foundation Requirements 1. Pour grout here up to top surface / plane of base plate 2. Nut 3. Washer 4. Base plate 5.
  • Page 3: Piping Requirements

    For safety and correct product usage, read the manual before this product is used. 3.3 Piping Requirements 1. Check that a section of straight pipe, with a length that is a minimum of five times its di‐ ameter, is installed between the suction side of the pump and the first elbow, or that a B&G Suction Diffuser is installed.
  • Page 4: Electrical Installation

    For safety and correct product usage, read the manual before this product is used. 4 Electrical installation Figure 1...
  • Page 5 For safety and correct product usage, read the manual before this product is used. Figure 2: Auxiliary connections Table 1: Position number Name Description Default setting Analog input 1 Power supply +24 VDC, max. 60 mA (to‐ Pressure sensor 1 tal, terminals 1 + 5) Configurable analog input 1 Electronic GND...
  • Page 6: Drive Operation

    For safety and correct product usage, read the manual before this product is used. Position number Name Description Default setting Digital Input 4 Configurable digital input 4, internal pull- Not selected up +24 VDC, contact current 6 mA Electronic GND Digital Input 5 Configurable digital input 4, internal pull- Not selected...
  • Page 7 • Generate a work report • Contact the assistance service. Download the App and connect the mobile device with the unit 1. Download the Xylem X App to the mobile device from App Store or Google Play by scanning the QR code: 2.
  • Page 8 Xylem builds products that are secure by de‐ Xylem Inc. Xylem and Bell & Gossett are registered trademarks of Xylem Inc. or one of its subsidiaries. 8200 N. Austin Avenue, Morton Grove, IL 60053 All other trademarks or registered trademarks are property of their respective owners.

This manual is also suitable for:

Bell & gossett e-1532 series

Table of Contents