Advertisement
Quick Links
Smart Energy Plug PAN45
This plug-in ON/OFF switch PAN45 is a devices displaying the Z-Wave Plus
also be used security enabled wireless switch, based on Z-Wave Plus
Wave Plus
TM
enabled with it regardless of the manufacturer, and can also be used in
other manufacturer's Z-Wave
TM
enabled networks. Remote On/Off control of the con-
nected load is possible with another manufacturer's wireless Controller. Each switch is
designed to act as a repeater. Repeaters will re-transmit the RF signal to ensure that the
signal is received by its intended destination by routing the signal around obstacles and
radio dead spots. Because PAN45 supports Security Command Class, it can learn with
Secured controller. Its functionality and supported command classes are identical when
included as a secure and non-secure device. It also have Zigbee as a repeater.
This plug-in ON/OFF switch is able to detect instance wattage (3000W/230Vac/13A)
and overload current (14.5A with resistive load) of connected lights or appliances. When
detecting overload state, the Switch will be disabled and it's On/Off button will be lock-
out of which LED will flash quickly. However, unplug and reconnect the switch will re-
set its overload condition to normal status.
Specification
Operating Voltage
Maximum Load (Ampere)
Range
Operating Temperature
Location
Frequency Range
RF Maximum Power
** Specifications are subject to change and improvement without notice.
TM
logo can
Troubleshooting
TM
technology. Z-
Symptom
The Switch not working
and LED off
The Switch LED illumi-
nating, but cannot control
the Switch of the load at-
tached
The Switch LED illumi-
nating, but the Detector
cannot control the Switch
LED keep flashing, but
cannot control
100V-240V~ 50Hz-60Hz
13A (Resistive load)
Minimum 40 m in door 100m outdoor line of sight
0°C ~ 40°C, 85%RH max
In door use
Z-Wave
TM
: 868.40MHz & 869.85MHz (EU)
Zigbee: 2405-2480MHz
+10dBm (Peak), -10dBm (Average) for Z-Wave
+10dBm for Zigbee
Cause of Failure
1.The Switch is not plugged into
1. Check power connections
the electrical outlet properly
2. Don't open up the Switch
2.The Switch break down
and send it for repair.
1. Set the ON/OFF switch of
1.Check if the load plugged into
the load attached to ON
the Switch has its own ON/OFF
2. Unprotected the switch or
switch
follow the instruction of pro-
2. The switch is protected
tection.
1. Not carry out association
1. Carry out association
2. Same frequency interference
2. Wait for a while to retry
Remove the load attached or
Overload occurs
check max. load cannot ex-
ceed 13A (Resistive load)
TM
Recommendation
Advertisement
Related Manuals for Philio PAN45
Summary of Contents for Philio PAN45
- Page 1 The Switch LED illumi- 1.Check if the load plugged into the load attached to ON radio dead spots. Because PAN45 supports Security Command Class, it can learn with nating, but cannot control the Switch has its own ON/OFF 2. Unprotected the switch or Secured controller.
-
Page 2: Product Overview
Warning: DANGER 1.Plug out to disconnect from power supply; Do not plug in line. Danger of electrocution! 2. Do not exceed the max rating. All works on the device may be performed only by a qualified and licensed elec- trician. Observe national regulations. Any works introducing changes into the configuration must be always per- formed with disconnected voltage. - Page 3 DSK string or scan the QR code. The Wave device, so associations may be QR Code can be found on PAN45 or in added or removed by a controller at any the box. Ex: time. Or If your controller requires to...
-
Page 4: Led Indication
2. The suitable ambient temperature for the Switch is 0°C~40°C. 3. Do not locate the Switch where exists combustible substances or any source PAN45 has red and green two colors led to show the switch status, the red one is for Z- Wave , the green one is for Zigbee. - Page 5 Type = 0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ] Value =0(0x00)] Report ON:[Command Class Switch Binary, Switch Binary Report, 2-1-3 Overload alarm report When PAN45 detects the current is more than 14.5A, it will send Alarm Report Value = 255(0xFF)] to Lifeline Group node. 1-2 BASIC_SET / SWITCH_BINARY_SET...
- Page 6 lated power consumption (KWH) or (3) AC load Voltage (V) or (4) AC load Scale = 0x00 (KWh) current (I) (5) load power factor (PF) to Z- Controller after receive the Precision = 2 Wave Meter Get Command from Z- Controller.
- Page 7 AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V) Meter Value 1 = 0x63(PF) (It means that the load power factor is 0.99) 2-2-5 AC load current ( I ) 3. Z- ’s Configuration Wave When receiving Meter Get Command, it will report Meter Report Command to Configuration Size Function...
- Page 8 3-2 KWH Meter Report Period: 3-8 Watt differential mode：The default setting is 1 (= 5%). If the setting is configured for 1hour (set value =6), PAN45 will report its Ac- Whenever Watt value of PAN45 changes over 5% of last reading value, it will cumulated Power Consumption (KWh) to Lifeline Group node every 1 hour.
- Page 9 Highest granted Security Class mental safe recycling. Association Group Highest granted Security Class Information Company of License Holder：Philio Technology Corporation Basic Highest granted Security Class Address of License Holder ：8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., Binary Switch Highest granted Security Class New Taipei City 24257, Taiwan(R.O.C)
Need help?
Do you have a question about the PAN45 and is the answer not in the manual?
Questions and answers