Yamaha MU100 Supplementary Manual page 31

MIDI data format
30 rr mm --
31 rr mm --
36 rr mm --
48 rr mm --
49 rr mm --
52 rr mm --
53 rr mm --
MSB 20-53 (for drums) is received when Multi Part
parameter PART MODE = DRUMS1...4.
*1 Refer to 1.2.4
*2 '--' indicates that the setting value is ignored.
*3 Adjusts the time after the note is played until vibrato
begins to take effect. The effect will begin more quickly
for higher values, and more slowly for higher values.
No effect if Bank Select MSB=127 is selected.
*4 No effect if Multi Part parameter PART MODE =
DRUM, DRUMS1...4.
1.2.22 RPN (Registered parameter number)
This message is used to specify part parameters such as Pitch
Bend Sensitivity or Tuning etc. as an offset value.
Use RPN MSB and RPN LSB to specify the parameter that
you wish to modify, and then use Data Entry (see 1.2.4) to
set the value of the specified parameter.
Control# Parameter
100 RPN LSB
101 RPN MSB
If the Multi Part parameter Rcv RPN = OFF, that part will
not receive this message.
The following RPN messages can be received.
32
Drum instrument chorus send
level
rr: drum instrument note number
mm: 00 - 127(0...maximum)
Drum instrument variation
send level
rr: drum instrument note number
mm: 00 - 127(0...maximum)
(when Variation Connection
= SYSTEM))
mm: 00, 01-127 (OFF,ON)
(when Variation Connection
= INSERTION))
Drum high pass filter cutoff
frequency
mm: 00 - 64 - 127
(-64...0...+63)
Drum EQ bass gain
mm: 00 - 64 - 127 (-64...0...
+63)
Drum EQ treble gain
mm: 00 - 64 - 127
(-64...0...+63)
Drum EQ bass frequency
mm: 04 - 40(32...2.0k [Hz])
Drum EQ treble frequency
mm: 28 - 58(500...16.0k
[Hz])
Data Range
0...127
0...127
MU100 MIDI
RPN Data Entry*1
MSB LSB MSB LSB
00 00 mm -- *2
00 01 mm ll
00 02 mm --
127 127 -- --
*1 Refer to 1.2.4
*2 '--' indicates that the setting value is ignored.
1.2.23 Assignable controller
By assigning a control change number of 0...95 to a part,
the specified effect can be controlled.
This device allows two control change numbers (AC1 and
AC2) to be specified for each part.
The following parameters specify the effect of AC1 and AC2.
• Multi Part Parameter
1. AC1, AC2 PITCH CONTROL
2. AC1, AC2 FILTER CONTROL
3. AC1, AC2 AMPLITUDE CONTROL
4. AC1, AC2 LFO PMOD DEPTH
5. AC1, AC2 LFO FMOD DEPTH
6. AC1, AC2 LFO AMOD DEPTH
• Effect1 Parameter
7. AC1, AC2 VARIATION CONTROL DEPTH
(Valid if Variation Effect is assigned to a part as Insertion)
The AC1 control change number is specified by the Multi
Part or A/D Part parameter AC1 CONTROLLER
NUMBER, and the AC2 control change number is specified
by the Multi Part or A/D Part parameter AC2 CONTROLLER
NUMBER.
1.3 Channel mode messages
These messages specify the basic operation of a part.
1.3.1 All Sound Off
This message silences all currently-sounding notes on the
corresponding channel.
However, the state of channel messages such as Note-on
and Hold-on will be maintained.
Parameter name and value range
Pitch bend sensitivity
mm: 00-24 (0...+24
semitones)
Specify up to 2 octaves in
semitone steps
Fine tuning
mm ll: 00 00 -100 cents
: :
mm ll: 64 00 0 cents
: :
mm ll: 127 127 +100 cents
[Note] mm ll: 00 127
(=-87.5) cents is
followed by 01 00
(=-87.4) cents.
Coarse tuning
mm: 40 - 64 - 88
(-24...0...+24 semitones)
RPN Null
This sets RPN and NRPN
numbers to an unset state.
Internal data is not affected.