Advertisement
Quick Links
DASH MOUNT
15-20 FORd F150
17-21 F250/350
DMFF-01
TOOLS
REQUIRED
- 4mm Allen bit
- 7mm hex socket
- 10mm wrench
- Trim pry tool
- Double sided tape
- Safety Glasses
- 15/64" Drill Bit
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
Before you install this kit —
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner's manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
SKILL
LEVEL
- Novice/Intermediate
- 1 (you)
Little skill level required, you can
easily install it by yourself however,
additional help will be useful
Read and understand all
PRODUCT
INSTALLATION
TIME
- 1 Hour
Time to install this should only
take about an hour
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
NEED HELP?
MANUAL
REQUIRED
855-680-9595
Advertisement
Related Manuals for DVB DMFF-01
Summary of Contents for DVB DMFF-01
- Page 1 6400 SYCAMORE CANYON BLVD. PRODUCT INSTALLATION MANUAL RIVERSIDE, CALIFORNIA 92507 855-680-9595 WWW.DV8OFFROAD.COM DASH MOUNT 15-20 FORd F150 17-21 F250/350 DMFF-01 TOOLS REQUIRED SKILL LEVEL TIME REQUIRED - 4mm Allen bit - Novice/Intermediate - 1 Hour - 7mm hex socket - 1 (you)
- Page 2 INSTALLATION MANUAL Begin by unpacking all items and inspecting for missing pieces or damage. If you have any concerns, please contact the company the product was purchased from. Extra hardware may be included with the product. HARDWARE INCLUDED (4) M6x20 Allen (4) M6 Lock Nuts (8) M6 Flat Washers (6) M6x14 Tapered Allen...
- Page 3 INSTALLATION MANUAL STEP 2 | Place (2) pieces of double sided tape on the bottom of the Dash Mount bracket. Peel off protective layer. STEP 3 | Remove factory dash pocket mat. NEED HELP? 855-680-9595...
- Page 4 INSTALLATION MANUAL STEP 4 | Place DV8 Dash Mount into factory poctet, press down firmly. Ensure the Dash Mount is algined with factory dash parting lines. STEP 5 | Remove the Dash Mount top by removing the (6) M6 screws using a 4mm Allen bit.
- Page 5 INSTALLATION MANUAL STEP 6 | Remove the dash speaker cover. With a frim grip, pull the front of the speaker cover up. STEP 7 | Using a 7mm Socket, remove the two bolts holding the dash pocket in place. STEP 8 | Using a trim pry tool, pry up the factory dash pocket.
- Page 6 INSTALLATION MANUAL STEP 9 | Disconnect the speaker wiring harness. STEP 10 | With the factory dash pocket removed and the DV8 Dash Mount double sided in place, use a marker to mark the 4 holes you will need to drill into the factory dash pocket.
- Page 7 INSTALLATION MANUAL STEP 11 | Using a 15/64ths drill bit, drill 4 holes in the factory dash pocket where previously marked. STEP 12 | Using a 4mm allen bit, 10mm wrench and provided M6 hardware, install the DV8 Dash Mount. NEED HELP? 855-680-9595...
- Page 8 INSTALLATION MANUAL STEP 13 | Re-install the connector for the dash speaker and then re-install the dash pocket by firmly pressing it into place until the clips are secure. STEP 14 | Use a 7mm socket to secure the dash speaker using the factory hardware.
- Page 9 INSTALLATION MANUAL STEP 15 | Use a 4mm allen bit with the provided M6 hardware to secure the top plate to the mount. STEP 16 | Congrats! You are finished with the install of the F- Series Dash Mount. NEED HELP? 855-680-9595...
Need help?
Do you have a question about the DMFF-01 and is the answer not in the manual?
Questions and answers