Table of Contents
Advertisement
TROUBLE SHOOTING
What happens if my soft close drawer is not closing properly?
It means that your soft close drawer is not engaged correctly. Follow the instructions on page 03 to re-engage the
soft close mechanism.
Why is my soft close drawer making a noise on closing, and not closing smoothly?
If the release tabs on the drawer are not lifted properly, then this may cause the cog to strip on the soft close
mechanism. Please contact Bath Co Customer Services for a replacement. This is not covered under warranty.
What are the dimensions of the cabinets – internal and external?
All dimensions can be found on our website – www.aouasbath.com or in our brochures.
Can I get an extra tap hole in my vanity top?
Yes – most tops we can put an extra tap hole in. This can be done at an extra cost of $60.00+GST per tap hole.
How to cut out a sink hole in Kordura surfaces?
These hybrid solid surfaces hold colour throughout and can be easily cut or drilled with a router, jigsaw or holesaw
PLUMBING RECOMMENDATIONS
» Single drawer units are designed to be plumbed with a bottle trap.
» Waste is not to be over-tightened to avoid stress on basin or top.
» A Contoured waste complete with a washer set top and bottom must be used on all
basins so as not to void the warranty
» We do not recommend the use of silicone when installing the contoured waste.
» Basin overflow must line up with waste opening.
» Waste overflow hole opening must not be blocked by sealant.
» Basins with fixing holes must be bolted back to the wall separately from the vanity unit.
CLEANING & MAINTENANCE
» To maintain the finish on your unit and top, only use a soft cloth, or a weak solution of non-abrasive detergent.
Do not use cleaners that incorporate isopropyl alcohol. Polymarble tops should only be cleaned with soapy
water and a soft cloth.
Kordura Surfaces: Regular cleaning is recommended. Use soapy water and a soft cloth when cleaning surface.
Do not use product with high alkaline & ph levels. Contact Bath Co directly to provide guidelines to polish
scratched and heavy stains.
» To restore accidental scratches, burns etc. on gloss painted finishes, rub gently with a very light cutting
compound. On matt or timber finishes contact the manufacturer.
» Mirrors should be cleaned with diluted methylated spirits only (dilute 1:10).
Remove all moisture caused by splashes, wet hands, or steam with a chamois or soft cloth after use.
Do not wipe the exposed edge of the mirror.
» To avoid deterioration; it is important mirrors are kept dry of any moisture.
» Bath Co warranty on mirrors applies for one year from the date of purchase
Email: admin@aquasbath.com website: www.aquasbath.com Tel:+757-85331862
16
Cleaning and Warranty
General Cleaning
Aquas Bath products are made from materials or sourced specifically for bathroom and laundry spaces. Our
vanities and cabinetry are designed to be water resistant, not waterproof. Care must be taken to immediately
dry spillage as well as ventilate your bathroom to eliminate moisture build up or humidity which will lead to
deterioration of materials and is not covered by warranty.
For all surfaces use a soft cloth and a weak solution of a non-abrasive detergent. Do not use cleaners with
isopropyl alcohol, high alkaline, acidic or any abrasive based cleaners. A moist microfibre cloth will give the
best results.
Cabinetry Finishes
Timber Veneer & Painted To clean
Aquas Bath timber veneer surfaces simply use a soft cloth and a weak olution of a non-abrasive detergent.
Do not use cleaners with isopropyl alcohol, high alkaline, acidic or any abrasive based cleaners.
Melamine
Melamine is low maintenance and easy to clean. Simply wipe down with a clean, damp cloth. With stubborn
grease and grime, use vinegar diluted with water or Selleys Sugar Soap. Always wipe with a damp cloth, then
a dry cloth after cleaning to remove moisture. Never use abrasive cleaners, cleaners with isopropyl alcohol,
high alkaline, acidic or any abrasive based cleaners.
Basins & Counter Top Vessels
Ceramic/Acrylic/Polymarble
Ceramic basin, just use water or clean soap to wipe with water is ok.
To clean acrylic surfaces use non-abrasive soap, It is recommended that the product surface is wiped dry
after each use to prevent the build up of soap and scum.
Polymarble
Mirrors
Keep your bathroom well ventilated to avoid condensation that can gather at the edges of your mirror.
Always protect from excessive moisture and ensure any moisture or condensation is wiped away
immediately.
Wipe your mirrors with a slightly moist microfibre cloth and then dry with a dry microfibre cloth.
DO NOT use any ammonia-based cleaning products (including glass cleaners), as these could corrode the
mirror's silver backing.
Warranty
Aquas Bath products carry a five (5) year warranty from the date of purchase. Proof of
purchase needs to be supplied by the purchaser when making a claim.
Aquas Bath warrants that in the manufacture of its products only high-quality workmanship
and materials have been used. If within the warranty period there should be a fault with
either materials or workmanship Plumbline will either (at its sole discretion) repair or replace
the faulty product, but will not be responsible for removal and installation costs.
This warranty does not cover damage by improper installation, abuse, accident, excessive wear, and tear,
improper care and maintenance, natural causes (sunlight and water), water temperatures above 55°C,
humidity, and over environmental conditions.
IMPORTANT NOTE: Under no circumstances are tile vanity cabinets and/or tops 'into' the wall.
Aquas Bath vanity cabinets & tops must be fitted to finished wall coverings. The Warranty does not cover any
vanity and/or top that has been tiled 'into' a wall i.e., fitting or fixing a vanity to a wall and tiling into the side
and around it, and/or tiling down and/or around the vanity top.
https://aquasbath.com/
admin@aquasbath.com
+86-757-85331862
17
Advertisement
Table of Contents
