Rockwell Automation Allen-Bradley 1734-AENTR Installation Instructions Manual

Rockwell Automation Allen-Bradley 1734-AENTR Installation Instructions Manual

Point i/o dual port ethernet/ip adapter

Advertisement

Quick Links

Installation Instructions
Original Instructions
POINT I/O Dual Port EtherNet/IP Adapter
Catalog Numbers 1734-AENTR, 1734-AENTRK, Series C
Topic

Summary of Changes

This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.
Topic
Updated Certifications
Page
1
5
5
5
6
6
7
7
8
9
10
13
Page
12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Allen-Bradley 1734-AENTR and is the answer not in the manual?

Questions and answers

Summary of Contents for Rockwell Automation Allen-Bradley 1734-AENTR

  • Page 1: Table Of Contents

    Installation Instructions Original Instructions POINT I/O Dual Port EtherNet/IP Adapter Catalog Numbers 1734-AENTR, 1734-AENTRK, Series C Topic Page Summary of Changes About the Adapter Before You Begin Install the Adapter Thumbwheel Settings Set the Chassis Size Set the Network Address Replace the Adapter Wire the Adapter Interpret Status Indicators...
  • Page 2 Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 3 Such locations correspond to Zone 2 classification according to UKEX regulation 2016 No. 1107 and ATEX directive 2014/34/EU. • May have catalog numbers followed by a “K” to indicate a conformal coating option. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 4 • This equipment shall be used within its specified ratings defined by Rockwell Automation. • Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage at the supply terminals to the equipment.
  • Page 5: About The Adapter

    Secure DIN rail to mounting surface approximately every 200 mm (7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail properly. See the Industrial Automation Wiring and Grounding Guidelines Rockwell Automation publication 1770-4.1, for more information.
  • Page 6: Thumbwheel Settings

    I/O modules, set the chassis size to 5. See the POINT I/O and ArmorPOINT® I/O Dual-port EtherNet/IP Adapters User Manual, publication 1734-UM017 for instructions on how to set the chassis size. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 7: Set The Network Address

    • Use the pen push thumbwheel switches on the adapter. • Use a Dynamic Host Configuration Protocol (DHCP) server, such as Rockwell Automation® BootP/DHCP. • Retrieve the IP address from nonvolatile memory. The adapter reads the thumbwheel switches first to determine if the switches are set to a valid number. You set the node address using the 3-position pen push thumbwheel switch using a pen tip.
  • Page 8: Wire The Adapter

    Do not connect 120/240V AC power to this supply. This DC supply will be connected to the internal power bus. WARNING: When used in a Class I Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with proper wiring method that complies with the governing electrical codes. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 9: Interpret Status Indicators

    One port @ 100 Mb and the other port @ 10 Mb. Solid yellow Link established with Port 1 and/or Port 2 @ 10 Mb. Flashing yellow Transmit or receive activity present on Port 1 and/or Port 2 @ 10 Mb. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 10: Specifications

    • 220 mA (Catalog numbers 1734-IR2, 1734-IR2E) Module location Starter module - left side of the 1734 system Maximum 31 direct connections for standard I/O or maximum 20 direct connections if any safety I/O module resides in the backplane. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 11 Ethernet ports 2, configured as Embedded Switch Ethernet network topologies supported Star, Tree, Daisy-chain/Linear, and Ring Ethernet connectors RJ-45, Category 5 Ethernet cable Category 5: shielded or unshielded Ethernet wire connections, max Wire Size Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 12 CNCA-C23-01 CNCA-C23-01 CCC Implementation Rule Explosion-Proof Electrical Products CCC: 2020122309111607 EtherNet/IP ODVA conformance tested to EtherNet/IP specifications See the Product Certification link at rok.auto/certifications for Declarations of Conformity, Certificates, and other certification details. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 13: Additional Resources

    1734-UM017 information on how to use the POINT I/O and ArmorPOINT I/O Dual Port EtherNet/IP adapters. Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 More information on proper wiring and grounding techniques. Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 14 POINT I/O Dual Port EtherNet/IP Adapter Installation Instructions Notes: Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 15 POINT I/O Dual Port EtherNet/IP Adapter Installation Instructions Notes: Rockwell Automation Publication 1734-IN041H-EN-P - February 2024...
  • Page 16 Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur Connect with us. Allen-Bradley, ArmorPOINT, expanding human possibility, ControlLogix, FactoryTalk, POINT Guard I/O, POINT I/O, POINTBus, Rockwell Automation, Studio 5000 Logix Designer, and TechConnect are trademarks of Rockwell Automation, Inc.

This manual is also suitable for:

Allen-bradley 1734-aentrk

Table of Contents