Cleaning And Maintenance - EINHELL AGILLO 36/255 BL Operating Instructions Manual

fray. If the line strikes wire fencing, it will break.
Trimming around trees
When trimming around tree trunks, approach
slowly so that the line does not strike the bark.
Walk around the tree, cutting from left to right.
Approach grass or weeds with the tip of the line
and tilt the line spool forwards slightly.
Warning: Take extreme care during mowing work.
When doing such work keep a distance of 100
ft. (30 m) between yourself and other people or
animals.
Mowing
When mowing down to the ground you will cut all
the vegetation. To do this, set the line spool at an
angle of 30° to the right. Place the handle in the
required position. Remember the increased risk of
injury to the user, watchers and animals, and the
danger of damaging property due to objects (for
example stones) being thrown up (Fig. 26).
Warning: Do not use the equipment to remove
objects from footpaths, etc.
The equipment is a powerful tool and can throw
small stones and other objects a distance of 50 ft.
(15 m) or more, causing injuries and damage to
cars, houses and windows.
Sawing
The equipment is not suitable for sawing.
Jamming
If the cutting blade jams as a result of attempting
to cut vegetation that is too dense, switch off the
engine immediately. Remove the grass and scrub
from the equipment before you restart it.
Preventing recoil
When you work with the blade, there is a risk of
recoil if it strikes solid objects such as tree trunks,
branches, tree stumps, stones or the like. This will
throw the equipment backwards in the direction
opposite to the rotation of the tool. This can cause
you to lose control of the equipment. Do not use
the blade near fences, metal posts, boundary
stones or foundations. For cutting dense stalks,
position the blade as shown in Fig. 27 to prevent
recoil.
6.3 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
Anl_Agillo_36_255_BL_SPK7_USA.indb 19 Anl_Agillo_36_255_BL_SPK7_USA.indb 19
EN
6.4 Battery capacity indicator (Fig. 21 / item
37)
Press the battery capacity indicator switch (38).
The battery capacity indicator (37) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depthdischarged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.

7. Cleaning and maintenance

HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
•
Use a brush to remove deposits from the
safety guard.
7.2 Replacing the line spool
Danger! Remove the battery packs!
1. Fig. 28 Press the line spool housing together
at the marked points and remove the spool
- 19 -
07.12.2023 14:06:06 07.12.2023 14:06:06