Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Disposal And Recycling - EINHELL GC-ET 4530 Original Operating Instructions

ding it at an angle of approx. 30° as you do so
(see Figure 7 and Figure 8).
•
Make several passes to cut long grass shor-
ter step by step from the top (see Figure 9).
•
Use the edge guide and the guard hood to
prevent unnecessary wear on the line.
•
Keep the grass trimmer away from hard ob-
jects in order to avoid unnecessary line wear.
Using the grass trimmer as an edge trimmer
(Fig. 12/13)
To cut the edges of lawns and fl ower beds, the
grass trimmer can be converted as follows:
•
Switch off the power supply of the electric
grass trimmer.
•
Pull the sleeve (Fig. 12/Item 10) to the rear.
•
Hold the sleeve in the rear position and rotate
the top handle through 180° (Fig. 12) until it
latches in place.
•
Now you have converted the electric grass
trimmer to an edge trimmer for cutting the
lawn vertically (Fig. 13).

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
Anl_GC_ET_4530_Set_SPK7.indb 23 Anl_GC_ET_4530_Set_SPK7.indb 23
GB
ingress of water into an electric tool increases
the risk of an electric shock.
•
Use a brush to remove deposits from the
safety guard.
8.2 Replacing the line spool (Fig. 14-16)
Important! Make sure that you pull out the
power plug before replacing the line spool!
•
Press the sides of the spool cover as shown
and remove the cover (Figure 14-15).
•
Remove the empty line spool.
•
Thread the ends of the line on the new line
spool through the eyelets in the spool recep-
tacle (Fig. 16).
•
Fit the spool cover back in the spool mount.
•
When you start the equipment again the line
will be cut to the perfect length automatically.
Caution! Bits of the nylon line could cause
injury when fl ung out!
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Spare line spool Art. no.: 34.056.85

9. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 23 -
02.02.2024 14:58:09 02.02.2024 14:58:09