Operation; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL GC-CT 18/26 Li Operating Instructions Manual

All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.

6. Operation

To obtain maximum performance from your grass
trimmer, please follow these instructions:
•
Never use the grass trimmer without the
guard.
•
Do not mow grass when it is wet. The best
results are achieved with dry grass.
•
To switch on your grass trimmer, press the
safety lock-off (Fig. 1 / Item 1) and the On/Off
switch (Fig. 1 / Item 2).
•
To switch off your grass trimmer, let go of the
On/Off switch again (Fig. 1 / Item 2).
•
Do not allow the grass trimmer near the grass
until the switch is pressed, i.e. the grass trim-
mer is in operation.
•
To cut properly, swing the machine sideways
while moving forwards. Keep the grass trim-
mer inclined at an angle of approx. 30° while
you do so (see Figs. 11 and 12).
•
If the grass is long, the grass must be cut
shorter in stages, starting from the tip (see
Fig. 13).
•
Use the guard hood to prevent unnecessary
wear.
•
To avoid unnecessary wear, keep the grass
trimmer away from hard objects.
6.1 Using the grass trimmer as an edge trim-
mer
To cut the edges of lawns and fl ower beds, the
grass trimmer can be converted as follows:
•
Remove the battery pack
•
Pull the lock for the rotatable motor head in
the direction of the arrow as shown in Fig. 8.
•
Turn the motor head through 90° in the requi-
red direction until it latches in place (Fig. 9).
•
Now you have converted the grass trimmer to
an edge trimmer for cutting the lawn vertically.
•
To convert the equipment back to its original
state, proceed in reverse order.
Anl_GC-CT_18-26_Li_Globus_SPK7.indb 18 Anl_GC-CT_18-26_Li_Globus_SPK7.indb 18
GB
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Before putting away or cleaning the grass trim-
mer, switch off and remove the battery pack.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend that you clean the equipment
immediately after you use it.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment. The ingress of water into an
electric tool increases the risk of an electric
shock.
•
Use a brush to remove deposits from the
safety guard.
7.2 Replacing the blade (Fig. 10)
IMPORTANT! Be sure to remove the battery
pack before replacing!
•
To remove the blade, push the blade inwards
and remove it through the larger opening as
shown in Fig. 10.
•
To fit the new blade, proceed in reverse order.
Make sure the blade locks into place correctly
as shown in Fig. 10.
7.3 Maintenance
•
There are no other parts inside the equipment
which require maintenance.
•
Check the tool for damage every time after it
has been used.
•
To ensure that the cordless grass trimmer
works safely, check at regular intervals that all
the screw connections are secure.
7.4 Ordering spare parts
Please provide the following information on all
orders for spare parts:
•
Model/type of the equipment
•
Article number of the equipment
•
ID number of the equipment
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
- 18 -
31.07.2023 15:22:25 31.07.2023 15:22:25