CONTENTS Hazard Identification & Safety Features & Benefits Installation Requirements & Dimensions Drafting Directions Control Dashboard Functions Switch Dashboard Functions Setting the Head Bail Open Gap How it works & Operation Modes Remote Control Button Mapping Cleaning & Maintenance Power Pack & Pressure Settings Trouble shooting Contact Information Taurus Auto Catch Cattle Crush |...
Hazard Identification & Safety Pay attention to all warning signs when the Crush is in use. The Taurus HD3 & HD5 Auto Catch Cattle Crush has moving gates positioned in multiple locations as Do not enter shown below. the squeeze or head bail area at any time as this may result in serious injury or death.
Features & Benefits Hot dip galvanised for long life. High quality industrial hydraulic valves. Hydraulic rams have stainless steel shafts for long Multifunction side gates allow safe and easy access to animal. life and corrosion protection. Simple to use push button controls. Optical sensors (European made) detect animal movements.
• • EID can run off a power supply or separate battery. Please read and understand the instructions before operating your Taurus HD3 or HD5 Auto Catch Cattle Crush. Scales & EID Compatibility Compatible with Te Pari T20, and T30 Scales, Gallagher 610/810/TSI Scales & Tru-test •...
Drafting Directions - 3 Way Draft Taurus Auto Catch Cattle Crush | Installation & Operators Manual 2023...
Page 7
Drafting Directions – 5 Way Draft Taurus Auto Catch Cattle Crush | Installation & Operators Manual 2023...
Page 8
Control Dashboard Features Head bail opening gap: Used to control the preset auto catch gap distance of the head bail. The higher the number the larger the opening gap. Draft gate reset time: Used to control the closing time to the drafting gates. Emergency stop: This isolates all power and discharges all hydraulic pressure.
Page 9
Switch Dashboard Features Race gate: Push button. Used to manually control the opening and closing of the race gate. Entry gate: Used to manually control the opening and closing of the Entry gate. Vet gate: Used to manually open or close the vet gate for operator access. Draft direction: Used to manually control the direction of the drafting.
Page 10
Setting the Head Bail for Auto Catch Setting the head bail gap is critical to efficient auto catching. If the gap is set too small the animal will hesitate and not advance through the head bail. Setting it too wide could allow the animal to get too far through causing a miss catch.
Page 11
How it works The Taurus Auto catch crush as four modes of operation to give total flexibility. MODE 1: Auto draft button on - Auto catch button on. When switched to Auto mode the crush will adjust ready for auto drafting/ auto catching. Use this mode to auto catch and auto draft as to weights selected on the scales panel.
Page 12
MODE 2: Auto draft button off - Auto catch button on. This mode allows for catching the animal at the head bail with the option of manual drafting. Set the Draft Gate switch to Straight before operation. Press Power button. Set the Head Bail Open Gap.
Page 13
MODE 3: Auto draft button on - Auto catch button off. When switched to Auto mode the crush will adjust ready for auto drafting. Use this mode to auto weigh and auto draft to weights selected on the scales panel. Set the Draft Gate switch to Straight before operation.
Page 14
MODE 4: Auto draft button off - Auto catch button off. (Manual mode) This disables all auto catching and drafting features and relies on the operator to use the control switches or remotes. Set the Draft Gate switch to Straight before operation.
Remote Control Button Mapping – HD3 You can only pair a remote inside the first 10 seconds of “Power On”. Head Bail Close Head Bail Open Squeeze Close Squeeze Open Entry Gate Press once to Open. Press again to Close Race Gate Press once to Open.
Page 16
Remote Control Button Mapping – HD5 You can only pair a remote inside the first 10 seconds of “Power On”. Head Bail Close: Press and hold Head Bail Close button & left-hand arrow = Opens Drafting Gate 4. Press and hold Head Bail Close button &...
Power Pack & Pressure Settings Powerpack Operation To turn the power pack on, rotate the red switch to the ‘ON’ position and press the blue button which powers the 24v circuit. Powerpack Pressure Regulator Pictured to the right is the main pressure switch on the hydraulic powerpack.
Page 19
Ram Pressure Regulators Below is the valve bank which controls the pressure to the head bail, squeeze, entry gate and draft gates. To increase pressure, loosen the lock nut and thread clockwise using an allen key in the head of the screw. Hydraulic Ram Pressure Settings: ...
Trouble Shooting Issue Cause Remedy Function switches won’t work. No power Check all power is supplied to the machine. Press “power on” button on Control dashboard. Ensure E stop is not pushed in. Entry doors not closed Check draft gate doors are closed. Check vet gate doors are closed.
Page 21
Auto Catch NOTE: BOXES IN YELLOW ARE PROCESSES THAT CAN BE CHANGES WHILE IN AUTOMATIC MODE. Issue Cause Remedy Head bail will not auto close. Auto Catch not on. Press Auto Catch button. Head bail catch distance Hydraulic pressure too Check fluid level.
Thank you for your purchase, enjoy your new Te Pari Taurus HD3 & HD5 Auto Cattle Crush from the Te Pari Team! Contact Information: Te Pari Products Australia 172 Jersey Drive, Epping, 3076 VIC Freephone 1800 650 682 Te Pari Products New Zealand...