Positioning the sensors (eyes) Anti backing hook Adjusting the clamp and weigh area width Adjusting the lead up race Trouble shooting guide 10–13 Hazard Identification EC Declaration of Conformity Machinery Contact us Back Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
S H E E P H A N D L I N G S YS TE M S Main components of your Racewell handler Draft Gates Clamp and Weigh Area Entry Gate Leadup Race Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
Power can be supplied via mains (110V AC to 240V AC) or via the 12 Volt battery leads supplied with the handler. The internal system is all 12 Volt AC power supply. Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
S H E E P H A N D L I N G S YS TE M S Remote Control All remotes have the following buttons: Tilt: Up / Down Clamp: Clamp/Release Draft gates The remote is powered by x2 AA batteries. Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
Tilt The tilt switch will move the Clamp and Weigh area up or down for access to the sheep. Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
Page 7
90–100 psi. If set to the lowest pressure the clamp wall will not move at all. It is important not to have the pressure to high for animal welfare. Release The release button will release the clamp. This button is used for releasing a sheep manually. Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
WEIGHING LARGER LAMBS OR SHEEP Please Note : Wool dust or debris covering any of the four eyes can affect operation. Make sure that the lenses of the eyes are clean at all times. Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
Adjusting the lead up race The lead up race can be adjusted for width at the top and bottom. A slight V configuration is best to prevent smaller animals turning around. Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
Also check they have no loose wool in front of them SHEEP ARE NOT BEING DRAFTED/SORTED Draft switch Communication cable may not be connected or scale configured correctly Check cable for damage Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
Page 11
Racewell HD S H E E P H A N D L I N G S YS TE M S DRAFTING THE WRONG WAY FOR PRESET WEIGHTS Ensure the manual draft switch is in the auto position Turn power off and on again on the Handler. This will force a communication handshake between the scales and handler EVERYTHING WORKS APART FROM THE DRAFTER...
Page 12
Racewell HD S H E E P H A N D L I N G S YS TE M S UNIT SLOWLY RELEASES AFTER SHEEP ARE CLAMPED Air may be leaking Check for air leaks Catch solenoid may be faulty Check solenoid Damage to cylinder piston Check piston...
Page 13
Racewell HD SH E E P H A ND LI N G S YS TE MS REMOTE CONTROL IS NOT WORKING PROPERLY OR AT ALL Flat remote control battery Check and replace as required Remote is not programmed to your unit Program remote to your unit by turning on the unit then: Remote EYES ARE NOT WORKING...
Be sure to keep your limbs, head and body out of the area of movement area. Draft gates may activate from signals received from the scale causing unexpected movement All the above hazards are applicable during manual or automatic operation. Te Pari Racewell HD3, HD4 & HD6 Operators Manual...
S H E E P H A N D L I N G S YS TE M S EC DECLARATION OF CONFORMITY MACHINERY (according to Annex II.1.A of the Machinery Directive) Te Pari Products Ltd hereby declares as manufacturer that the Racewell Sheep Handler with specifications: Machine...
Page 16
44 Ricky Way, Epping Melbourne, 3076 VIC PHONE : 1800 650 682 EMAIL sales.au@tepari.com : accounts.au@tepari.com accounts Warranty Claims and Returns Form https://www.tepari.com/contact-us/warranty-claim/ Thank you for your purchase, enjoy your new Te Pari Racewell HD Sheep Handlers from the Te Pari team...