Page 1
YACHT ROUTER MICRO Installation Manual SERIES 6 The easiest way to stay online. version 1.0...
Page 2
Read carefully. For better understanding check video tutorials on our website. Register your product for software update notifications. Thank you.
Page 3
The contents of this manual are well prepared by Locomarine Networks d.o.o. While we try to improve our equipment at all times, Locomarine Networks d.o.o. shall incur no liability based on contents, updates or modification of the contents, or the lack of contents in this manual.
Page 4
IMPORTANT: It is solely on end-user to set transmitting power value for WIFI Booster to comply with regulations of country where product will be used. Regulations and online WIFI power calculators (EIRP - Equivalent Isotropically Radiated Power) are widely available on the Internet. Locomarine Networks d.o.o. cannot by responsible by any means for improper setup. Transmittion power is set and regulated via Yacht Router Control software.
Page 5
PREFACE SAFETY INSTRUCTIONS ELECTRICAL SHOCK HAZARD: Do not open enclosure of the equipment if you are not qualified to do it. TURN OFF THE POWER IMMEDIATELY IF WATER LEAKS INTO THE EQUIPMENT OR AN OBJECT DROPS INTO THE EQUIPMENT: Continue operating the equipment could cause electrical shock or fire. Contact your nearest distributor or dealer for service. DO NOT DISASSEMBLE THE EQUIPMENT OR MODIFY THE EQUIPMENT: Improper disassemble or modification could cause electrical shock, fire, or personal injury.
CONTENT INTRODUCTION ABOUT YACHT ROUTER MICRO s6 FEATURES WHAT IS IN THE PACKAGE PORTS AND CONNECTORS INSTALLATION CONNECTING POWER SUPPLY INSTALLING ANTENNAS INSERTING SIM CARDS SETUP SETUP TECHNICAL SPECIFICATIONS HARDWARE DETAILS NETWORK DETAILS OUTLINE DRAWINGS...
CHAPTER 1 - INTRODUCTION 1.1. ABOUT YACHT ROUTER MICRO S6 Yacht Router Micro s6 (Yacht Router Micro in further text) is designed for installation on smaller vessels. You can establish single Vessel WIFI network that you can connect to mobile networks (4G/3G).
CHAPTER 2 - INSTALLATION 2.1. CONNECTING POWER SUPPLY There are two ways to power Yacht Router Micro: • DC in 8-30 V connector directly from vessel battery (with supplied DC power cable with connector 2 m) • DC in 8-30 V connector using supplied AC/DC power adaptor Most common way is to connect Yacht Router Micro directly to vessel battery using 2 m supplied DC power cable.
CHAPTER 3 - SETUP 3.1. SETUP Once you finished hardware installation you need to install Yacht Router Control software to setup and control Yacht Router: Once you install the software refer to USER MANUAL how to use it. It is available for download on our website www.yachtrouter.com You can also check VIDEO TUTORIALS on our website www.yachtrouter.com...
CHAPTER 4 - TECHNICAL SPECIFICATIONS 4.1. HARDWARE DETAILS WAN, LAN, Backbone ports Total number of Ethernet ports: 5 Ethernet Satellite WAN ports: not available Ethernet Vessel Networks (LAN) / Backbone ports: 5 Max. data rate on Ethernet port: 1000 Mbps Add-on Modules support WIFI Booster: 1 Mobile Expander: yes...
Page 13
CHAPTER 4 - TECHNICAL SPECIFICATIONS GNSS receiver Channels: 22 tracking / 66 acquisition Supported system: GPS/GLONASS/BeiDou/Galileo/QZSS Sensitivity: -158 dBm Antenna: no separate antenna - GNSS use mobile antennas Power, environment and dimensions DC power supply input range: 10-30 V Max. power consumption: 9 W Operating temperature range for internal unit: -10 to +50 °C Operating humidity range: 5-95 % non-condensing IP Protection: IP50...
CHAPTER 4 - TECHNICAL SPECIFICATIONS 4.3. OUTLINE DRAWINGS All dimensions in mm.
Page 16
WIFI power calculators (EIRP - Equivalent Isotopically Radiated Power) are widely available on the Internet. It is solely up to user to comply with country regulations and Locomarine List of approved antennas: Networks d.o.o.
Page 17
APPENDIX INDUSTRY CANADA NOTICE TO USERS Notice: To satisfy IC RF exposure requirements for mobile and base station transmission devices, a separation distance of 63 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Need help?
Do you have a question about the MICRO 6 Series and is the answer not in the manual?
Questions and answers