Summary of Contents for Locomarine STANDARD 5 Series
Page 1
YACHT ROUTER STANDARD Installation Manual The easiest way to stay online. version 1.0...
Page 2
Read carefully. For better understanding check video tutorials on our website. Register your product for software update notifications. Thank you.
Page 3
The contents of this manual are well prepared by Locomarine Networks d.o.o. While we try to improve our equipment at all times, Locomarine Networks d.o.o. shall incur no liability based on contents, updates or modification of the contents, or the lack of contents in this manual.
Page 4
IMPORTANT: It is solely on end-user to set transmitting power value for all Yacht Router WIFI components to comply with regulations of country where product will be used. Regulations and online WIFI power calculators (EIRP - Equivalent Isotropically Radiated Power) are widely available on the Internet. Locomarine Networks d.o.o. cannot by responsible by any means for improper setup.
Page 5
PREFACE SAFETY INSTRUCTIONS ELECTRICAL SHOCK HAZARD: Do not open enclosure of the equipment if you are not qualified to do it. TURN OFF THE POWER IMMEDIATELY IF WATER LEAKS INTO THE EQUIPMENT OR AN OBJECT DROPS INTO THE EQUIPMENT: Continue operating the equipment could cause electrical shock or fire. Contact your nearest distributor or dealer for service. DO NOT DISASSEMBLE THE EQUIPMENT OR MODIFY THE EQUIPMENT: Improper disassemble or modification could cause electrical shock, fire, or personal injury.
CONTENT INTRODUCTION ABOUT YACHT ROUTER STANDARD MODEL VERSIONS FEATURES WHAT IS IN THE PACKAGE PORTS AND CONNECTORS INDICATORS INSTALLATION CONNECTING POWER SUPPLY CONNECTING ADDITIONAL MODULES AND DEVICES SETUP TECHNICAL SPECIFICATIONS HARDWARE DETAILS NETWORK DETAILS OUTLINE DRAWINGS...
CHAPTER 1 - INTRODUCTION 1.1. ABOUT YACHT ROUTER STANDARD Yacht Router Standard is designed for installation on vessels with single or dual satellite Internet source (VSAT, Inmarsat, Iridium etc). It will provide the ability to establish three vessel networks (e.g. Owner, Guests, Crew) as WIFI and cable version. Each Vessel Network can be simultaneously connected to same or different Internet source. For example: you can connect Owner network to the internet via VSAT (using additional satellite equipment), Guest network to the Internet over 4G mobile system (via additional Mobile Expander module) while in the same time Crew network can access Internet over WIFI Hotpost in marina (via additional WIFI Booster module).
1 Achieved with 9dBi outdoor antenna. As actual range depends on many factors Locomarine Networks d.o.o. do not guarantee specified range of connectivity. 2 Achieved with 9dBi outdoor antenna and VIP mobile provider. As actual range depends on many factors Locomarine Networks d.o.o. do not guarantee specified range of connectivity.
CHAPTER 1 - INTRODUCTION 1.4. WHAT IS IN THE PACKAGE When shipped, all devices are wrapped in plastic bags that protect them from humidity. Devices are then placed into a cardboard box. A bag containing accessory items is placed inside the box too.
CHAPTER 1 - INTRODUCTION 1.5. PORTS AND CONNECTORS Yacht Router Standard is equipped with following ports and connectors. Vessel Network 1 SAT 2 Vessel Network 2 SAT 1 Backbone ports 1-5 Vessel Network 3 Reset (not in use) DC out 1-3, 24 V DC out 4-6, 24 V DC in Fuse...
CHAPTER 2 - INSTALLATION 2.1. CONNECTING POWER SUPPLY There are two ways to power Yacht Router Standard: • directly from boat battery (10-30 V DC) • via supplied AC/DC power supply and DC power cable adaptor Most common way is to connect Yacht Router Standard directly to vessel battery using 2 m supplied DC power cable. Power cable consist of RED and BLACK wire. Connect RED wire to positive (+) and BLACK wire to negative (ground -) power source on your vessel power supply system (battery).
Page 13
CHAPTER 2 - INSTALLATION Connection via supplied AC/DC power supply and DC power cable adaptor.
CHAPTER 2 - INSTALLATION 2.2. CONNECTING ADDITIONAL MODULES AND DEVICES You can upgrade your Yacht Router with following equipment: Mobile Expander It is device that will give you posibility to connect Yacht Router to 2G/3G/4G mobile networks. It is equipped with high power modem and with additional outdoor antennas it is possible to get 30+ NM offshore connection.
Page 15
CHAPTER 2 - INSTALLATION Example of various modules and devices connected to the system.
CHAPTER 2 - INSTALLATION 2.3. SETUP Once you finished hardware installation you need to install Yacht Router Control software to setup and control Yacht Router: Once you install the software refer to USER MANUAL how to use it. It is available for download on our website www.yachtrouter.com You can also check VIDEO TUTORIALS on our website www.yachtrouter.com...
CHAPTER 3 - TECHNICAL SPECIFICATIONS 3.2. NETWORK DETAILS Yacht Router Standard has reserved IP ranges that cannot be used by other connected equipment: Support network 10.10.10.0/24 Reserved range 10.80.0.0/12 Yacht Router Standard IP reservation details: Backbone Network 10.80.0.0/16 Vessel Network 1 Gateway: 10.81.0.1 Free static range: 10.81.0.20 - 10.81.0.99 DHCP: 10.81.0.100 - 10.81.255.254...
CHAPTER 3 - TECHNICAL SPECIFICATIONS 3.3. OUTLINE DRAWINGS All dimensions in mm.
Page 20
IMPORTANT: It is solely on end-user to set transmitting power value for all Yacht Router WIFI components to comply with regulations of country where product will be used. Regulations and online WIFI power calculators (EIRP - Equivalent Isotopically Radiated Power) are widely available on the Internet. It is solely up to user to comply with country regulations and Locomarine Networks d.o.o.
Page 21
List of approved antennas: Omni Directional (pole), model Locomarine MOB 7 ANTENNA INSTALLATION: antennas from other products MUST NOT BE CO-LOCATED within 20 cm range to each other to satisfy FCC regulations.