1. Manuals
  2. Brands
  3. Locomarine Manuals
  4. Network Router
  5. YACHT ROUTER Standard 4G
  6. User manual

Locomarine YACHT ROUTER Standard 4G User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
READ CAREFULLY and DO NOT PANIC.
version 1.1
www.yachtrouter.com

Advertisement

Table of Contents
loading

Related Manuals for Locomarine YACHT ROUTER Standard 4G

Summary of Contents for Locomarine YACHT ROUTER Standard 4G

  • Page 1 User Manual READ CAREFULLY and DO NOT PANIC. version 1.1 www.yachtrouter.com...

  • Page 2: Table Of Contents

    RoHS COMPLIANT ..3 INTRODUCING YACHT ROUTER SOLUTION ..3 DISCLAIMER ..3 WARNING ..3 SAFETY INSTRUCTIONS ..3 ABOUT YACHT ROUTER STANDARD 4G ..4 FEATURES ..5 SPECIFICATIONS ..5 9.1. WAN, LAN, Backbone networks ..5 9.2.

  • Page 3: Copyright Notice

    1. COPYRIGHT NOTICE Locomarine d.o.o. reserves the rights to alter the products described in this manual at any time without prior notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

  • Page 4: About Yacht Router Standard 4G

    7. ABOUT YACHT ROUTER STANDARD 4G Yacht Router Standard 4G is intended for installation on boats and yachts with single or dual satellite Internet source (VSAT, Inmarsat, Iridium etc). It will give you ability to establish three vessel WIFI networks (Client-to-Vessel) that you will be able to independently connect to other WIFI networks (e.g.

  • Page 5: Features

    8. FEATURES - high power remote Vessel-to-Shore WIFI module (PoE, 500mW, b/g/n, outdoor) for simplified installation and zero coax cable signal loss - high power 4G/3G/2G module (250-2000mW) - 3x Client-to-Vessel WIFI network (b/g) - Hotspot on single Client-to-Vessel WIFI network (Guest) - 3x LAN port (100 Mbps) - 2x WAN port (for satellite Internet equipment) - 3x Backbone LAN port...

  • Page 6: Mobile Network

    9.5. Mobile network Integrated modems: 1 LTE frequency bands (MHz): 800/900/1800/2100/2600 WCDMA frequency bands (MHz): 900/2100 GSM/GPRS/EDGE frequency bands (MHz): 900/1800/1900 Max. download rates (Mbps): 100 Max. upload rates (Mbps): 50 Max. transmit power in LTE/4G (dBm): 24 Max. transmit power LTE/4G (mW): 250 Max.

  • Page 7: Installation Instructions

    WIFI Extension cable (WLEC-01) to install Client-to-Vessel WIFI antenna (WLAN-A-05) on a better position. Yacht Router Standard 4G is equipped with Remote Vessel-to-Shore WIFI module. It is used for connecting Yacht Router Standard 4G to Hotspots in marinas or similar WIFI access points. Remote Vessel-to-Shore WIFI module is Power over Ethernet device that use single LAN (e.g.

  • Page 8: Connecting Computer Or Other Lan Equipment

    (CAT5P-03) that is supplied with a package. Connect Gigabit PoE injector as you can see on a photo below this text. You can use any of three BACKBONE (1, 2, 3) and DC OUT (1, 2, 3) ports on Yacht Router Standard 4G. If you plan to install Remote Vessel-to- Shore WIFI module on an outdoor location you will have to make custom-made LAN cable that will pass trough bottom screw cap of a module.

  • Page 9: Connecting Power Supply

    Inserting SIM card Yacht Router Standard 4G will work with any Standard GSM (ID-000) SIM card. If you have Standard or nano SIM card you will have to obtain proper adaptor. Insert SIM card as it is showed on the following photo:...

  • Page 10: Led Indicator And Ports

    LED indicator and Ports Yacht Router Standard 4G has multiple LED indicators. Red LED on a power button indicate that device is powered on. Yacht Router Standard 4G is equipped with eight Ethernet ports. Each port is equipped with green and yellow LED indicator for data traffic indication.

  • Page 11: Setup Procedure

    YR Control Software is developed for Microsoft Windows 7 and Windows 8 operating system but if will probably work on Vista and XP. Locomarine does not offer support for any Yacht Router system that is not installed on Windows 7 or Windows 8 operating system.

  • Page 12: Yacht Router 4G Control Software

    Once you start Yacht Router 4G Control Software you will see Connected to Yacht Router and button Enter in green colour. In upper right corner you will see Contact Us button that will give you Locomarine Support contacts. If your device is not able to con- nect to Yacht Router you will see Connecting... message.
  • Page 13 If you press green Shore WIFI button under Vessel Network 1 drop-down menu will appear. In that manu you can change your Internet source (WAN) for Vessel Network 1. You will do the same for Vessel Network 2 and Vessel Network 3. Each Vessel Net- work can simultaneously be connected to different WAN source.

  • Page 14: Setup Screen

    Configurations button Description: open Configuration setup screen. Contact Us button Description: open Contact Us screen with Locomarine contact details. Support Network button Description: open Support Network connections menu. To use this feature Vessel Network 1 must be connected to Internet. You will use this feature if you need support from our Technical support.

  • Page 15: Configuration Screen

    First value you should setup is Yacht Router Lock Password. VERY IMPORTANT: Set your Lock Password! If you do not set it anyone who is connected to any Vessel Network (WIFI or LAN) with installed Yacht Router 4G Control Software on any of supported device will be able to control Yacht Router. It can cause many unwanted and very expensive consequences (e.g. if someone switch Internet source on your Vessel Network from WIFI Hotspot in marina to your Inmarsat FleetBroadband while you are watching movie on YouTube). To setup Lock Password press Configurations button to open Configurations screen. 13.4. Configuration screen Setup screen is divided in three sections: Global Settings section Reset to Factory Default button Description: open menu to Confirm that you want to reset to factory defaults. Revert To Saved Configuration button Description: open menu to Confirm that you want to revert to saved configuration.

  • Page 16: Satellite Wan Network Setup

    Enter password in Lock Password field and press UPDATE button. Your Yacht Router is now protected with a password. From now on, every time you start Yacht Router 4G Control Software on any supported device (computer, iPhone, iPad, Android) you will be prompted to enter password on Initial screen.
  • Page 17 If you press ADVANCED button in upper right corner you will get access to advanced setup and info. WAN IP Address configuration section DHCP buttons On (changeable) Default value: Description: enabling or disabling DHCP (Dynamic Host Configuration Protocol), Renew button will renew settings when DHCP is enabled, Refresh button refresh data in IP, SUBNET, GATEWAY, DNS 1, DNS2 fields. IP field Default value: not defined (changeable)

  • Page 18: Mobile Wan Networks Setup

    13.6. Mobile WAN Networks setup Once you press Mobile WAN Networks button on Setup screen you will open WAN Network setup screen that consist of: Main section WAN Name field 4G Mobile (changeable) Default value: Description: enter name of your Mobile connection (e.g. Vodafone Greece). WAN Status button Description: turn on or off modem.
  • Page 19 If you press ADVANCED button in upper right corner you will get access to advanced setup and info. WAN IP Address configuration section DHCP buttons On (changeable) Default value: Description: enabling or disabling DHCP (Dynamic Host Configuration Protocol), Renew button will renew settings when DHCP is enabled, Refresh button refresh data in IP, SUBNET, GATEWAY, DNS 1, DNS2 fields. IP field Default value: not defined (changeable)

  • Page 20: Shore Wifi Wan Networks Setup

    13.7. Shore WIFI WAN Networks setup Once you press Shore WIFI WAN Networks button on Setup screen you will open WAN Network setup screen that consist of: Main section WAN Name field Shore WIFI (changeable) Default value: Description: enter name of your Ship-to-Shore connection (e.g. Marina Hotspot). WAN Status button Description: turn on or off connection to Shore WIFI.
  • Page 21 WAN IP Address configuration section DHCP buttons Default value: On (changeable) Description: enabling or disabling DHCP (Dynamic Host Configuration Protocol), Renew button will renew settings when DHCP is enabled, Refresh button refresh data in IP, SUBNET, GATEWAY, DNS 1, DNS2 fields. IP field not defined (changeable) Default value: Description: show IP (Internet Protocol) address.
  • Page 22 To check Shore WIFI Network status and connectivity details click on gray field/button as specified on the following picture. Click here to get precise data about mobile network and connectivity status. You will get following statuses: ssid, band, frequency, wireless protocol, tx rate, rx rate, bssid, signal strength, tx signal strength, noise floor, signal to noise ratio, tx ccq, rx ccq, overall tx ccq, last ip, autentification-type, group encryption, management protection, compression. For more information about meaning of above specifications consult Internet or IT specialist. www.yachtrouter.com...

  • Page 23: Vessel Network Setup

    13.8. Vessel Network setup Once you press Vessel Network 1, Vessel Network 2 or Vessel Network 3 button on Setup screen you will open Vessel Network setup screen that consist of: Main section Name field Default value on Vessel Network 1: Vessel Network 1 (changeable) Default value on Vessel Network 2: Vessel Network 2 (changeable) Vessel Network 3 (changeable)

  • Page 24: Hotspot

    13.9. Hotspot Yacht Router Standard 4G is equipped with Hotspot feature. This feature is available only on a Vessel Network 2 WIFI network. Once you enter Vessel Network 2 setup press ADVANCED button in upper right corner. Next to DHCP-Client List that was described on previous page Hotspot section will appear. It consist of:...

  • Page 25: Online Remote Support

    Team Viewer software. You can also download compact version of Team Viewer on our website www.yachtrouter.com under Support section or simply click here. YACHT ROUTER NETWORK DETAILS Yacht Router Standard 4G has reserved IP ranges that cannot be used by other connected equipment: Support network: 10.10.0.0/16 Reserved range: 10.80.0.0/12 Yacht Router Standard 4G IP reservation details Backbone Network: 10.81.0.1/16 Vessel Network 1: Gateway: 10.81.0.1...

  • Page 26: Yacht Router Configuration Tool

    Locomarine manufactures marine electronic products which are marketed and supported worldwide via the Locomarine distributor, dealer and partner network. Each and every Locomarine distributor, dealer and partner is committed to service and support the products in accordance with the market’s needs and requirements. In addition, the Locomarine distributor, dealer and partner networks are obliged to support the products irrespective of who sold and installed the product.

Table of Contents