Advertisement
EN 100
8.
Q522.3E LA
Table 8-2 Tint settings
Colour Temp.
Cool
Normal
Warm
Cool
Normal
Warm
Cool
Normal
Warm
8.4
Option Settings
8.4.1
Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these specific
ICs (or functions) is made known by the option codes.
Notes:
•
After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
•
The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the Mains
switch (the NVM is then read again).
8.4.2
Dealer Options
For dealer options, in SAM select "Dealer options" and then
"Personal options".
Table 8-3 Dealer options
Menu item
Subjects
Personal Options Picture Mute On
Virgin Mode
8.4.5
Option Code Overview
Table 8-4 Option code overview (subject to change and as available at time of publishing)
CTN MODEL
22PFL6403D/12
32PFL6403D/12
42PFL6403D/12
Important: After having edited the option numbers as
described above, you must press OK on the remote control
before the cursor is moved to the left!
8.5
Reset of Repaired SSB
A very important issue towards a repaired SSB from a service
repair shop, implies the reset of the NVM on the SSB.
A repaired SSB in service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Alignments
R
G
B
22"
Not available at time of publishing
32"
Not available at time of publishing
42"
Not available at time of publishing
Options Description
Picture is muted / not muted in case
no input signal is detected at input
Off
connectors
On
TV starts up / does not start up (once)
with a language selection menu after
Off
the Mains switch is turned "on" for the
first time (virgin mode)
Displ. code
Group 1
174
33280
136
33280
130
33280
8.4.3
(Service) Options
Select the sub menu's to set the initialisation codes (options) of
the set via text menus.
8.4.4
Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or "option byte") represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set and in Table
"Option code overview".
Example: The options sticker gives the following option
numbers:
2
C
•
33280 04110 06209 45160
•
10158 00096 00004 00000
The first line (group 1) indicates hardware options 1 to 4.
Example: option no. "2" contains the "cabinet type".
The second line (group 2) indicates software options 5 to 8.
Example: option no. "5" contains the "display code".
Every 5-digit number represents 16 bits (so the maximum value
will be 65536 if all options are set).
When all the correct options are set, the sum of the decimal
values of each Option Byte (OB) will give the option number.
See table "Option code overview" for the options. Please note
that this overview is indicative (subject to change). Always refer
to the sticker in the TV-set as leading.
Diversity
Not all sets with the same Commercial Type Number (CTN)
necessarily have the same option code!
Use of Alternative BOM
An alternative BOM number usually indicates the use of an
alternative display. This results in another Display Code thus in
another Option code. Refer to chapter 2 "Safety Instructions,
Warnings, and Notes".
04110
06209
45160
04110
06219
45160
04110
06219
45160
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool.
Group 2
10158
00096
00004
10120
00096
00004
10114
00096
00004
00000
00000
00000
Advertisement
