Download  Print this page

Advertisement

XES Synergix™ Controller
8855 Setup Manual for
Firmware 7.0

Advertisement

   Also See for Xerox Synergix 8855

   Related Manuals for Xerox Synergix 8855

   Summary of Contents for Xerox Synergix 8855

  • Page 1 XES Synergix™ Controller 8855 Setup Manual for Firmware 7.0...
  • Page 2 This page left intentionally blank.
  • Page 3: Safety Information

    If you are not sure of the type of power available, consult your local power company. XES Synergix 8855 Controller Setup Manual for Firmware 7.0 The power supply cord is the disconnect device for this equipment.
  • Page 4: Emc Notices

    EMC Notices Australia/New Zealand Changes or modifications to this equipment not specifically approved by Fuji Xerox Australia Pty. Limited may void the user's authority to operate this equipment. Shielded cables must be used with this equipment to maintain compliance with the Radiocommunications Act 1992.
  • Page 5: Japan

    Changes or modifications to this equipment not specifically approved by Fuji Xerox Limited may void the user's authority to operate this equipment. Shielded cables must be used with this equipment to maintain compliance with the Voluntary Control Council for Interference by Information Technology Equipment regulations.
  • Page 6: Trademark Notices

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Trademark Notices XEROX®, XES™, Synergix™, The Document Company, and the identifying product names and numbers herein are trademarks of XEROX CORPORATION. PostScript is a trademark of Adobe Systems Incorporated. AutoCAD is a registered trademark of Autodesk, Inc.
  • Page 7: Table Of Contents

    Platforms supported ... 9 Auto Port Sensing ... 9 Client Software ... 9 XES Synergix 8855 Controller Setup Manual for Firmware 7.0 PC/DOS platform: ... 9 PC/Windows 95 and Windows 98 platforms:... 9 PC/Windows NT 4.0 and Windows 2000 platforms: ... 9 UNIX platform:...
  • Page 8 XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Software Supported ... 15 Data Formats Supported... 15 SCSI Cable Description ... 15 Preparing the 10/100 Ethernet Port ... 16 Overview ... 16 Enable Controller Ethernet Port ... 16 Network Protocols Supported: ... 17 TCP/IP ...
  • Page 9: Purpose Of This Manual

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 The reference sets of the test print pages should be stored with the machine service log, behind the service door of the XES Synergix 8855 printer. NOTE: The printer must have bond paper installed to enable the printing of any test print.
  • Page 10: Setting The Controller Port Defaults

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Setting the Controller Port Defaults The AccXES controller will operate with one, two, or all ports active. A 10/100 Ethernet interface, supporting TCP/IP is standard on the controller. To prepare the AccXES controller to print: •...
  • Page 11: Floor Space Requirements

    6 inches (15 cm) 12 inch (31cm) AccXES Controller Figure 1 - Floor Space Requirements XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Power Requirements The controller requires the following, depending on source power: • 15 ampere at 115 volts •...
  • Page 12: Power Locations

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Power Locations The positions of the power connection and power switch are shown in this figure. Power Switch AC Input Figure 2 - Power Connection...
  • Page 13: Controller Ports Location

    Controller Ports Location Parallel 10/100 Ethernet Scanner SCSI UI Data Figure 3 -Port Connections on Rear XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Host Serial Host SCSI Folder Connection Printer Interface UI Power...
  • Page 14: Front Panel Leds

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Front Panel LEDs The controller has four status LEDs in on the front panel. The functions of these LED’s are as follows: • LED1 – Color Green, labeled “Ready” –Indicates the controller is powered-up and ready to process incoming jobs.
  • Page 15: I/o Download Of Firmware Upgrades

    Factory Defaults and you may lose your custom settings for the Active Parameters set. For Active Parameters Set information, see “Setting the Active Parameters Option” in this manual. XES Synergix 8855 Controller Setup Manual for Firmware 7.0...
  • Page 16: Controller Specifications

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Controller Specifications Physical Characteristics The controller is a tower positioned adjacent to the XES Synergix 8855 Printer. Electrical Requirements 100 - 250 VAC auto-ranging power supply. Agency Approvals Safety: UL 1950, CA22.2 No. 950 (CUL), EN 60950 (CE Mark)
  • Page 17: Job Printing And Processing Specifications

    ADI Drivers for AutoCAD R13/14 • HDI Drivers for AutoCAD 2000 and 2000i • PostScript PPD System Print Driver XES Synergix 8855 Controller Setup Manual for Firmware 7.0 • AccXES Client Tools • Web Printer Manager Tool PC/Windows NT 4.0 and Windows 2000 platforms: •...
  • Page 18: Unix Platform

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Job Printing and Processing Specifications (continued) UNIX platform: • tftp puts • telnet • lpr/lpd support • Access Client Tools • Web Printer Manager Tool Job Control Language HP-PJL with custom extensions.
  • Page 19: Extended Processing Options

    Control Panel Lockout • Scan-to-Net (DDS option) • Job Accounting (DDS option) XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Number of copies 1 to 999 Electronic Collation More than 200 E. (Assumes 10:1 compression ratio.) Folding and Stacking Optional Online Folder is available.
  • Page 20: Preparing The Serial Port

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Preparing the Serial Port The Host Serial Port This port requires a null modem serial cable to be connected from the controller host serial port to the workstation serial port. It is necessary to use the appropriate software drivers or system commands to send jobs to the controller.
  • Page 21: Data Formats Supported

    CABLE PART NUMBERS 600T02058 Serial Cable, 9-pin to 9-pin 600T02073 Null Modem Adapter XES Synergix 8855 Controller Setup Manual for Firmware 7.0...
  • Page 22: Preparing The Parallel Port

    Parallel Cable Description The cable connector is a standard, “mini-Centronics” P1284C connector. A ten foot, high density P1284A to P1284C cable is available (Xerox part number 98S03302). The maximum length of the parallel cable must not exceed 12 feet (3.66 m).
  • Page 23: Preparing The Host Scsi Port

    By default, the host SCSI port bus termination is enabled. Figure 6 – Typical Web PMT, Ports Setup Page XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Software Supported •...
  • Page 24: Preparing The 10/100 Ethernet Port

    XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Preparing the 10/100 Ethernet Port Overview The controller contains an embedded 10/100Mhz Ethernet network interface port. Enable Controller Ethernet Port Use the Printer_Defaults>Network>TCP-IP menu of the Web PMT to set the net mask, IP address, gateway.
  • Page 25: Network Protocols Supported

    • Web Printer Manager Tool • tftp puts • lpr/lpd support • AccXES Client Tools XES Synergix 8855 Controller Setup Manual for Firmware 7.0 Preparing the 10/100 Ethernet Port (continued) Data Formats Supported • HP-GL, HP-GL2 • HP-RTL • CalComp 906 /907 /951 /PCI •...
  • Page 26 XES Synergix 8855 Controller Setup Manual for Firmware 7.0 This page left intentionally blank.
  • Page 27 This page left intentionally blank.
  • Page 28 ©2001 XESystems, Inc. All rights reserved. Printed in the United States of America ® XEROX , XES Synergix 8855 and 8855 Digital Solution, the digital box icon, AccXES, and the acronym XES are trademarks of Xerox Corporation. 701P36856 April 2001...

Comments to this Manuals

Symbols: 0
Latest comments: