Table of Contents
Advertisement
Quick Links
DASH MOUNT
22+ (3RD GEN) TOYOTA TUNDRA
DMT2-01
TOOLS
REQUIRED
- 4mm Allen Wrench
- 10mm Wrench
- 11/32 Drill Bit
- Double Sided Tape
- Safety Glasses
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
Before you install this kit —
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner's manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
SKILL
LEVEL
- Novice/Intermediate
- 1 (you)
Little skill level required, you can
easily install it by yourself however,
additional help will be useful
Read and understand all
PRODUCT
INSTALLATION
TIME
- 1 Hour
Time to install this should only
take about an hour
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
NEED HELP?
MANUAL
REQUIRED
855-680-9595
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DV8 OFFROAD DMT2-01
Summary of Contents for DV8 OFFROAD DMT2-01
- Page 1 1. Name of purchase location Customer Service: 855-680-9595 2. Bar Code on side of box DV8 Offroad is not responsible for any bodily injury or harm to you 3. Date above bar code or your vehicle as a result of an improper install.
- Page 2 INSTALLATION MANUAL Begin by unpacking all items and inspecting for missing pieces or damage. If you have any concerns, please contact the company the product was purchased from. Extra hardware may be included with the product. HARDWARE INCLUDED (5) M6x16mm Allen Bolts (5) M6 Nutserts (10) M6 Flat Washers (5) M6 Nylon Lock Nuts...
- Page 3 INSTALLATION MANUAL STEP 3 | Disconnect the 12v power supply plug. Reinstall factory dash pocket. STEP 4 | Place the DV8 Dash Mount in to the factory dash pocket. Press down firmly. NEED HELP? 855-680-9595...
- Page 4 INSTALLATION MANUAL STEP 5 | Using a 4mm Allen wrench, remove the (4) M6 Countersunk head screws holding down the DV8 Dash Mount top. STEP 6 | With a firm grip, remove the factory dash pocket with the DV8 Dash Mount bracket in place.
- Page 5 INSTALLATION MANUAL STEP 7 | Use a marker to mark the (5) mounting holes you will need to drill to secure the DV8 Dash Mount. STEP 8 | Remove the DV8 mounting bracket. STEP 9 | Using a 11/32nds drill bit, drill the (5) mounting holes.
- Page 6 INSTALLATION MANUAL Optional Step: Provided are M6 Nutserts and Lock nuts, either can be used with the provided M6 Allen head screws to secure the DV8 Dash Mount to the factory dash pocket. If desired, install the nutserts using a rivet gun.
- Page 7 INSTALLATION MANUAL STEP 10 | Secure the DV8 Dash Mount bracket to the factory dash pocket using a 4mm Allen wrench or bit and the provided M6 hardware. STEP 11 | Reconnect the 12v Power supply plug. STEP 12 | Install the factory dash pocket and DV8 Dash mount bracket.
- Page 8 INSTALLATION MANUAL STEP 13 | Secure the DV8 Dash Mount Top to the bracket using a 4mm Allen wrench and provided (4) M6 countersunk hardware. Plug in any charing cables if desired and feed them through the top mount prior to securing it.
Need help?
Do you have a question about the DMT2-01 and is the answer not in the manual?
Questions and answers