Vocoder Parameters - Korg KingKORG NEO Parameter Manual

KingKORG NEO Parameter Guide
Src (Source) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[EG1...MIDI3]
Selects the signal (source) that will be the source of modulation.
EG1, EG2 EG1, EG2
LFO1, LFO2 LFO1, LFO2
Velocity Keyboard velocity (playing dynamics).
PitchBend Pitch bend (joystick: X-axis left/right)
JS+Y Modulation (joystick: Y-axis upward)
JS-Y Modulation (joystick: Y-axis downward)
Keyboard tracking (position).
Keyboard tracking works according to the
pitch as controlled by pitch bend, transpose,
KeyTrack
and modulation sequencer. It does not reflect
pitch changes produced by vibrato or virtual
patching.
The function specified for the [MIDI Ctrl] page
MIDI1, MIDI2, MIDI3
parameters "MIDI1," "MIDI2," or "MIDI3".
Dest(Destination) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[Off...R/D Time]
This selects the parameter (destination) that will be controlled by the
modulation. For example if you select Tune, modulation will be applied to the
overall pitch of the timbre.
Off
—
Pitch The pitch of the entire timbre.
Portamento The Pitch page Porta.Time.
Osc1Tune The Osc1 page TUNE.
Osc2Tune The Osc2 page TUNE.
Osc3Tune The Osc3 page TUNE.
Osc1Ctr1 The Osc1 page Control1.
Osc2Ctr1 The Osc2 page Control1.
Osc3Ctr1 The Osc3 page Control1.
Osc1Ctr2 The Osc1 page Control2
Osc2Ctr2 The Osc2 page Control2
Osc3Ctr2 The Osc3 page Control2
Osc1Level The Mixer page Osc1Level
Osc2Level The Mixer page Osc2Level
Osc3Level The Mixer page Osc3Level
Cutoff The Filter page Cutoff
Resonance The Filter page Resonance
FcEG1Int The Filter page EG1Int
FcKeyTrk The Filter page KeyTrack
EG1Attack The EG1-Filter page Attack
EG1Decay The EG1-Filter page Decay
EG1Sustain The EG1-Filter page Sustain
EG1Release The EG1-Filter page Release
EG2Attack The EG2-Amp page Attack
EG2Decay The EG2-Amp page Decay
EG2Sustain The EG2-Amp page Sustain
EG2Release The EG2-Amp page Release
LFO1Freq The LFO1 page Freq.
LFO2Freq The LFO2 page Freq.
AmpLevel The Amp page Level
Panpot The Amp page Pan
Patch1Int The V.Patch1 page Int
Patch2Int The V.Patch2 page Int
Patch3Int The V.Patch3 page Int
Patch4Int The V.Patch4 page Int
Patch5Int The V.Patch5 page Int
Patch6Int The V.Patch6 page Int
Pre Drive DRIVE/FREQ knob of PRE FX
Mod Depth
Mod Speed
R/D Depth
R/D Time
Int (Intensity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[–63...+63]
Specifies the depth of the effect produced by the modulation source. With a
setting of "+00", there will be no modulation.
Setting example for "SOURCE" and "DEST"
Src Dest
EG1/EG2 Pitch
EG1/EG2 Panpot
LFO1/LFO2 Pitch
LFO1/LFO2 Cutoff
LFO1/LFO2 AmpLevel
LFO1/LFO2 Panpot
Velocity AmpLevel
KeyTrack Panpot
PitchBend Panpot
3 .

Vocoder parameters

We recommend that you edit the vocoder parameters while looking at the
vocoder block diagram (OM:
v01: Vocoder
Vocoder SW (Vocoder Switch)
This switches the Vocoder function on/off.
Off:
The vocoder function will be off. The front panel VOCODER button will be
unlit, and the program will not use the vocoder.
On:
The vocoder function will be on. The front panel VOCODER button will be
lit, and the program will use the vocoder. You'll be able to select and edit
the vocoder parameter pages ("v02: Voc.Carrier" – "v18: Voc.Amp").
v02~03: Voc . Carrier (Vocoder Carrier)
On these pages you'll specify the input level for the carrier, the original signal
where the vocoder effect is applied.
Timb A Level (Timbre A Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[000...127]
This specifies the output level of Timbre A (carrier).
Timb B Level (Timbre B Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[000...127]
This specifies the output level of Timbre B.
- 13 -
DEPTH knob of MOD FX
SPEED knob of MOD FX
DEPTH knob of REV/DELAY
TIME knob of REV/DELAY
The EG1 or EG2 will vary the pitch of
the entire timbre over time.
The EG1 or EG2 will vary the pan over
time. By setting two patches to Patch#Int
settings with the opposite (+/–) value you
can create more complex panning.
Vibrato will apply at the rate of LFO1 or
LFO2.
Wah will be applied at the LFO1 or
LFO2 frequency.
Tremolo will be applied at the LFO1 or
LFO2 frequency.
Auto pan will be applied at the LFO1 or
LFO2 frequency.
Velocity (keyboard playing strength) will
affect the volume.
Keyboard position will gradually change
the pan; lower notes at the left, and
higher notes at the right.
Joystick operation will move the sound
left or right.
p.17).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Off, On]
Parameters