Table of Contents
Advertisement
KingKORG NEO Parameter Guide
g10: Common>Knob
Mode (Knob Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Jump, Catch, ValueScale]
This specifies what will happen when the physical position of the front panel
knob does not match the actual value of the parameter.
Jump:
When you turn a knob, the parameter value will jump to the value
indicated by the knob. We recommend this setting when you're editing,
since it will be easy to hear the result of your editing.
Catch:
When you turn a knob, the parameter value will not change until the knob
reaches the position corresponding to the actual current value. We
recommend this setting when you're performing, since it lets you avoid
making abrupt changes in the sound.
ValueScale:
When you turn a knob, the parameter value will increase or decrease in a
relative manner in the direction that you're turning. When you turn the
knob and it reaches the full extent of its motion, the parameter will also be
at its maximum or minimum value. Once the knob position matches the
parameter value, the knob position and parameter value will subsequently
be linked.
If the parameter value does not change
In some cases, the parameter value will not change when you turn a front
panel knob.
This means that Mode is set to "Catch." In "Catch" mode, the value will not
change until the knob position matches the actual value of the parameter that
you're editing (the value shown in the main display).
"Catch" mode prevents the value from changing abruptly and causing an
unnatural change in the sound when you use the knob. Once the knob position
matches the actual value, the knob and the value will be linked.
If "Jump" mode is selected, using the knob will cause the actual value to
immediately jump to the position of the knob.
Suppose that you've turned knob [1] to edit a
certain parameter, and that the knob is in the
position shown.
Suppose that you switch programs, and the actual value of
the parameter assigned to the knob is now at the position
indicated by the triangle in the illustration. (Moving a knob
slightly will make the actual value appear.)
The parameter value will not change until you turn the knob
to that position.
Once the knob has reached the position
corresponding to the actual value, the parameter
value and the knob position will be linked, and the
value will change as you turn the knob.
g11: Common
Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Off, On]
This specifies whether internal memory will be protected. With the factory
settings, this is "Off".
Off:
You'll be able to write to internal memory.
On:
The following Write procedures will be prohibited.
• Writing a program
• Loading the factory-set data
• Receiving a data dump
• Program category and favorite button assignments
g12~13: Power Save
This is where you can adjust power management settings.
You can dim the displays or make the displays and LEDs turn off to reduce
power consumption when the unit has not been used for a time. The
illumination will return to its previous state when you use or play the unit.
Mode (Power Save Mode) . . . . . . . . . .[DispLow, DispOff, Disp&LEDOff]
This specifies what will happen when power conservation mode is activated.
DispLow:
The display will dim.
DispOff:
The displays will turn off.
Disp&LEDOff:
The displays and LEDs will turn of.
Time (Power Save Time) . . . . . . . . . . . . . . . . . . . . . . . [30sec, 1min, 5min, 15min]
This page is available if Mode is set to "DispOff" or "Disp&LEDOff".
This specifies the length of time until the displays and LEDs will go dark in
power save mode.
30sec, 1min, 5min, 15min:
The illumination will go dark if the unit is not used for 30 seconds, 1
minute, 5 minutes, or 15 minutes respectively.
g14: Power Off
AutoPOff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[Disable, 4hours]
The KingKORG NEO will automatically power-off if its keyboard, knobs, or
buttons when there has been no user input for a period of time. With the
factory settings, this is set to "4hours".
Disable:
The Auto Power Off function will be disabled. The power will not turn off
automatically.
4hours:
The power will turn off automatically when four hours have elapsed
without using the buttons, knobs, or keyboard.
When the power turns off, the settings that you had been editing will be
lost. If you want to keep your edits, you must save them.
- 18 -
Parameters
Advertisement
Table of Contents
