Maytag MHN30PDBGW Installation Instructions Manual page 14

CODE EXPLANATION CODE EXPLANATION
H. 01 SUPER CYCLE UPGRADE PRICE r 800 TOP SPIN SPEED RPM
(Skipped unless super cycle pricing is enabled.) : : :
: : : r. 800 This can be selected from the following spin
H. O01 This represents the number of coin 1 required to speeds: 600 rpm, 750 rpm, 800 rpm, 1000
upgrade a base cycle to a super cycle. Advance (displays as 999) rpm. Step between speeds by
from 0-39 by pressing the PERM. PRESS keypad. pressing the PERM. PRESS button. Factory
> Press the DELICATES AND KNITS button once pre-set for 800 rpm.
to advance to next code. + Press the DELICATES AND KNITS button once
h. 01 SUPER CYCLE TYPE to advance to next code.
(Skipped unless Super Cycle pricing is enabled.) U. 00 PENNY INCREMENT OFFSET
h. O01 This represents the Super Cycle upgrade option. : e e e
U. 00 This option is not supported for European Models
Press the PERM. PRESS button to step through and the value must be set to 00.
upgrade options 1-3 as follows:
01 - enhanced wash, extra 3 minutes of wash > Press the DELICATES AND KNITS button once
. vas : to advance to next code.
tumble in addition to the programmed wash time.
. Al. 00 PREWASH LENGTH
02 - extra rinse for all cycles.
03 - both 01 and 02. Ai. 00 This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select
~~ Press the DELICATES AND KNITS button once between ve) and 7 minutes by pressing the PERM.
to advance to next code. PRESS button.
Cd COIN/DEBIT OPTION > Press the DELICATES AND KNITS button once
Cd Both coin & debit selected. Press the QUICK to advance to next code.
CYCLE button 3 consecutive times to change this A2. 03 FINAL SPIN LENGTH
section. A2. 03 This is the number of minutes of final high speed
J. C_ Coins selected, debit disabled. Press the QUICK spin. Choose from 3-8 minutes by pressing the
CYCLE button 3 consecutive times to change this PERM. PRESS button.
selection. + Press the DELICATES AND KNITS button once
J. _d Debit card selected, coins disabled. This is the to advance to next code.
factory default for PN models. Press the QUICK
CEE putton 3 consecutive times to change this if cycle counter (9 0C) is selected, the following is true:
, t a 100 Number of cycles in HUNDREDS. 1 02 = 200
Jd. Ed Enhanced Debit is self-selected when a 200 Number of cycles in ONES. 225= 25
Generation 2 card reader is installed in the
washer. The Ed option cannot be manually TOTAL CYCLES = 225
selected or deselected. This is 'VIEW ONLY' and cannot be cleared.
> Press the DELICATES AND KNITS button once
to advance to next code. ~ Press the DELICATES AND KNITS button once to
L. 00 PRICE SUPPRESSION OPTION advance to next code.
This option causes the customer display to show
'ADD' or 'AVAILABLE' rather than the amount of if money counter (1.0C or 1.C0) is selected, the following
money to add. (Used mainly in debit installations.) is true:
L. 00 Not Selected 'OFF' 300 Currency amount in HUNDREDS. 3 01 = 100.00
' , 400 Currency amount in ONES. 468= 68.00
L. PS Selected 'ON.' Press the QUICK CYCLE button : fod
once for this selection. 500 Currency amountin HUNDREDTHS. 575= 00.75
TOTAL = 168.75
> Press the DELICATES AND KNITS button once
to advance to next code. END OF SET-UP PROCEDURES
n. CE CLEAR ESCROW OPTION EXIT FROM SET-UP MODE
When selected, money held in escrow for lm PD Models: Reinstall access door.
30 minutes without further escrow or cycle m PN MODELS WITH PROGRAMMING SWITCH:
activity will be cleared. .
Turn key clockwise and remove.
00 Not Selected 'OFF'. ™ PN MODELS WITHOUT PROGRAMMING SWITCH:
CE Selected 'ON'. Press the QUICK CYCLE button Set-up mode can be exited by using procedures from the
once for this selection. Service Access Code section.
> Press the DELICATES AND KNITS button once
to advance to next code.
14