Unpacking; Before Commissioning; Assembly - Scheppach DP18VARIO Instruction Manual

Warning:
• The noise emission values can vary from the speci-
fied values during the actual use of the electric tool,
depending on the type and the manner in which the
electric tool is used, and in particular the type of
workpiece being processed.
• Try to keep the stress as low as possible. For ex-
ample: Limit working time. In doing so, all parts of
the operating cycle must be taken into account (such
as times in which the electric tool is switched off or
times in which it is switched on, but is not running
under a load).
7.

Unpacking

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, keep the packaging until the expiry of
the warranty period.
ATTENTION
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!

8. Before commissioning

Before each use, always check:
• On/off switch incl. emergency stop switch for prop-
er function.
• Always carry out a visual inspection before use.
• Check safety devices, electrical controls, electrical
cables and screw connections in particular for dam-
age and firm seating. If necessary, replace dam-
aged parts before operating the machine.
• Make sure that the table clamping lever is tightened
before you start the machine.
• Make sure that the drill bit is securely fastened in
the chuck.
• Remove the chuck key from toothed chucks. Before
switching the device on, check whether the chuck
key has been removed.
9.

Assembly

Column and machine foot, Fig. 4
1. Set the machine foot (1) down on the ground or
the workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the four hexagonal bolts (23) to fasten the
column into the base plate and tighten them using
a hexagon spanner (A).
Assembling the drilling table, Fig. 7
1. Insert the drilling table (4) into the drilling table
holder (22).
2. Use a clamping handle (3) to secure the drilling
table (4).
Installing the machine head and column, Fig. 8
1. Place the machine head (17) on the column (2).
2. Align the drill's spindle with the table and the base
plate and tighten the Allen screws that are located on
the side of the machine head. (Allen key, 4 mm / C)
Installing the handle, Fig. 9+10
1. Screw three handles (10) tight in the handle brack-
et's thread. Use the hexagon spanner (A) to do this.
2. Screw the speed adjustment lever (6) into the han-
dle bracket for speed adjustment. Use the hexa-
gon spanner (A) to do this.
Installing the folding swarf protector and the drill
chuck, Fig. 11+12+13
1. Push the folding swarf protector (11) onto the spin-
dle on the machine head and use a Phillips head
screwdriver to secure it.
2. Push the tapered mandrel (21) into the drill chuck
(12) with a sharp jolt.
3. Then push the tapered mandrel (21) into the drill
spindle. To do this, guide the drill chuck (12) includ-
ing the cone (21) into the spindle until is reaches the
stop and then turn it until it slides a little further into
the spindle. Now insert the drill chuck (12) including
the cone into the spindle. Check that it is tight.
Note: To protect against corrosion, all bare parts are
heavily greased at the factory. Before placing the drill
chuck (12) on the spindle, both parts must be made
completely free of grease with an environmentally
friendly solvent, so that optimal power transmission is
guaranteed.
www.scheppach.com GB | 33