Advertisement
Quick Links
REMOTE CONTROL EXPANSION KIT
The Model 172-94X is an expansion kit intended for use when installing Xtra Link 2's in more that one room.
It includes only the parts needed for each additional room, thus avoiding the unnecessary duplication of
couplers, emitters and coax jumper cables.
The 172-94X kit consists of the following supplied parts:
291-00
Fig. 1 172-94X Kit Parts
1. One 291-10 Infrared (IR) Receiver. It is placed at the remote room location to receive IR signals
-from the handheld remote controller.
2. One INJ94 Injector. This unit, located in the Remote Room, injects the remote control signal into the
room-to-room coaxial cable (along with the TV signal) and passes it to the CPL94B Coupler in the
Main room. It also allows quick connection of the 291-00 IR Receiver and 781RG Power Supply
cables.
3. One short coaxial cable. Connects the INJ94 Injector to the TV in the Remote Room.
4. A 781C-00 Power supply. This plugs into an unswitched 120V AC outlet to provide power to the
291-00 IR Receiver.
INSTALLATION
Fig. 2 shows the connections necessary when using a 172-94X expansion kit to provide remote control from
an additional room.
Begin by installing a standard 172-94 kit, for one of the remote rooms. (Refer to the owner's manual for the
Xtra Link 2 Model 172-94, for basic system connections). Next, using one of the 172-94X kits, install it into
the second remote room, making connections as shown in Fig. 2. Note that a 2-way RF splitter is used to
split the coax signal to each of the remote rooms. This splitter must be a DC passing type, such as the
Xantech Model 200-00.
NOTE: If RF amplifier(s) are used anywhere in the line of coaxial cable between the CPL94B Coupler and
the INJ94 Injectors, you must use a Xantech BYPASS94 KIT to route the IR commands around such
amplifier(s).
ADVANCED MULTIROOM HOOKUP
Fig. 3 shows an advanced system using six 172-94 plus five 172-94X Expansion Kits, in a multiroom
installation. The connection concept is essentially the same as in Fig. 2, except for the additional splitters,
RF amplifiers, etc. that need to be taken into consideration.
INSTALLATION INSTRUCTIONS
172-94X
XTRA LINK 2
INJ94
IR Receiver
TV
INJ94 INJECTOR
IR
RCVR
Coax Jumper Cable
®
781C-00
Injector
Power Supply
INPUT
+12 V
1
Advertisement
Related Manuals for Xantech 172-94X
Summary of Contents for Xantech 172-94X
-
Page 1: Installation Instructions
REMOTE CONTROL EXPANSION KIT The Model 172-94X is an expansion kit intended for use when installing Xtra Link 2's in more that one room. It includes only the parts needed for each additional room, thus avoiding the unnecessary duplication of couplers, emitters and coax jumper cables. -
Page 2: Technical Information
Fig. 2 Applying One 172-94X Kit For a Second Remote Rooms Keep the following items in mind when installing the system: 1. Each of the RF splitters used must be DC passing types, such as the Xantech models 200-00 (2-way) and the 202-00 (4-way), as shown. - Page 3 Six Remote Rooms, five with 172-94X Expansion Kits, configured in the same 291-00 781C-00 Power Supply (6) RF Signal IR Signal 284M or 286M Dual Emitter (not included) Satellite Receiver Fig. 3 Using Multiple 172-94X Kits For Additional Remote Rooms 172-94X manner as shown in Fig.
- Page 4 Injectors, through the coax cables to the IR (emitter) jack on the coupler, without shorts to ground. B. Use a Xantech 179-99 Test-IR (or a Blink IR Emitter) plugged into the IR (emitter) jack on the coupler to verify that the IR signal is being received from each room.