Related Manuals for Barco RML W6
Summary of Contents for Barco RML W6
- Page 1 Please read this manual before using this projector RLM W6 USER’S GUIDE User’s Guide Downloaded From projector-manual.com Barco Manuals...
-
Page 2: Table Of Contents
Installing the projector Connecting the projector to other devices 12V Trigger connection RGB connection RGBs connection IR INPUT connection S-Video/Video connection COMPONENT connection Turning on the projector Changing OSD language Adjusting screen orientation Adjusting the projector lens Downloaded From projector-manual.com Barco Manuals... - Page 3 OSD Menu Tree OSD Menu description OSD Description INPUT IMAGE LAYOUT LAMP ALIGNMENT Control Service Lamp and filter maintenance Lamp replacement Cleaning the filter Simple troubleshooting and definition of the LED indicators LED STATUS Projector specifications Downloaded From projector-manual.com Barco Manuals...
-
Page 4: Warning, Notices And Safety Instructions
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. The lamp(s) in this product contain mercury.This product could contain other electronic wastes that might be hazardous if not handled properly.Please consult your local/state/ federal regulations regarding disposal or recycling. Downloaded From projector-manual.com Barco Manuals... -
Page 5: Warning And Safety Instructions
Electric shock To protect your projector, avoid turning on the projector during lightning storms and unplug it from the wall outlet. This will prevent sudden electrical surges caused by the lightning from damaging the projector. Downloaded From projector-manual.com Barco Manuals... - Page 6 Should you encounter problem with the projector, please seek assistance from your local dealer or qualified service personnel. Do not attempt to service the projector yourself so that you would not be exposed to high voltage or other potential hazards. Downloaded From projector-manual.com Barco Manuals...
-
Page 7: Notices You Should Read Prior To Theinstallation Of The Projector
Installation environment for the projector You should avoid installing the projector at place of excessive dampness, dust or smoke. If installation in such environment is unavoidable, be sure to have the interior of the projector Downloaded From projector-manual.com Barco Manuals... - Page 8 Downloaded From projector-manual.com Barco Manuals...
- Page 9 Warning, Notices and Safety Instructions Name and quantity of toxic/hazardous substances/elements contained in the product Downloaded From projector-manual.com Barco Manuals...
-
Page 10: Projector Parts And Functions
Press this button to confirm Displays the cause of problem selection of OSD item; you can (i.e. temperature, fan, lamp choose from "Select Item" or or system) that has led to access "Sub Menu" configurations. projector malfunction. Downloaded From projector-manual.com Barco Manuals... - Page 11 (YPbPr) image source and chan- nel (Hs, Vs) source. RGBHV/SOG Standard 15-pin VGA connection socket to connect to RGB, high-definition component input or PC.The projector will automatically detect the resolution of the input signal. IO Control (Input/Input control panel) Downloaded From projector-manual.com Barco Manuals...
-
Page 12: Bottom View
M8x15 3 screws 157.50 147.50 M8x40 Set weight 3 bolts center line weight center line 152.50 Ceiling Mount Order Info: 1. R9849999-Ceiling mount 2. R9841260-Short Pulley 400mm to 765mm 3. R9841261-Long Pulley 800mm to 1165mm Downloaded From projector-manual.com Barco Manuals... -
Page 13: Range Of Effective Remote Control Signalreception
Note8: If the infrared receiver is exposed to fluorescent lamp or strong sunlight, the remote control may not operate normally. Note9: Refer to the regulations enforced by your local government on the disposal of used batteries; improper disposal could damage the environment. Downloaded From projector-manual.com Barco Manuals... -
Page 14: Quick Installation Of The Projector
4. Remove the lens cover on the projector before starting it AC MAINS AC POWER SWITCH 100-240 Volts 50/60Hz STBY Press the button on the Connect to a wall outlet projector or the button on the remote control to start up the projector. Downloaded From projector-manual.com Barco Manuals... - Page 15 6.Adjusting focus and zoom. Press the MENU button on the remote control and choose Alignment Lens Control; then use the buttons to adjust the lens' focus (clarity). Downloaded From projector-manual.com Barco Manuals...
- Page 16 Press the button on the projector or the button on the remote control to turn off the projector. When the projector has been turned off, the cooling fan will remain in operation for approximately 90 seconds. Downloaded From projector-manual.com Barco Manuals...
-
Page 17: Throw Distance
For details, please contact your local dealer. Frontal projection - desktop installaion Advantages: easy to install can be easily moved or adjusted easy to operate. Disadvantage: occupies floor space and limits seating capacity. Downloaded From projector-manual.com Barco Manuals... - Page 18 Disadvantage: requires an additional room for Disadvantage: requires an additional room installation relatively higher costs for installation relatively higher for installation. costs for installation. Screen Mirror Downloaded From projector-manual.com Barco Manuals...
-
Page 19: Horizontal And Vertical Lens Shift
Note: when the lens is in the neutral position (i.e. without horizontal or vertical shift), the center of the projection should be aligned with the center of the screen. Downloaded From projector-manual.com Barco Manuals... -
Page 20: Installing The Projector
Retractable screen or other Sleeve = Ground 12V device Tip = +12V 12V TRIGGER RGB-S 350mA RS-232 IR ext. S-VIDEO VIDEO YUV 1 RGB-HV/SOG B/Pb R/Pr HDMI HDMI RGBHV / YUV 2 Downloaded From projector-manual.com Barco Manuals... -
Page 21: Rgb Connection
RS-232 IR ext. S-VIDEO VIDEO YUV 1 AC MAINS AC POWER SWITCH 100-240 Volts 50/60Hz RGB-HV/SOG B/Pb R/Pr HDMI HDMI Connect to a wall outlet RGBHV / YUV 2 Desk Top or Notebook Downloaded From projector-manual.com Barco Manuals... -
Page 22: Rgbs Connection
IR INPUT jack to extend the effective signal reception range. Remote control IR sensor IR repeater 12V TRIGGER RGB-S 350mA RS-232 IR ext. S-VIDEO VIDEO YUV 1 (3.5-mm mini phono jack) RGB-HV/SOG B/Pb R/Pr HDMI HDMI RGBHV / YUV 2 Downloaded From projector-manual.com Barco Manuals... -
Page 23: S-Video/Video Connection
COMPONENT1 SCART or COMPONENT2 jacks. 12V TRIGGER RGB-S 350mA RS-232 IR ext. S-VIDEO VIDEO YUV 1 RGB-HV/SOG B/Pb R/Pr HDMI HDMI RGBHV / YUV 2 DTV set-top-box or other (YPbPr) component (YPbPr) input source Downloaded From projector-manual.com Barco Manuals... -
Page 24: Turning On The Projector
By factory default, the OSD menu of the projector is displayed in English. If you wish to switch to a different language, you can go to MENU CONTROL Language and choose the language you prefer for the OSD. Downloaded From projector-manual.com Barco Manuals... -
Page 25: Adjusting Screen Orientation
Frontal projection - ceiling mode Press MENU ALIGNMENT Ceiling Mode and choose ON; the projector is now configured for "frontal projection - ceiling mode". Correct Picture canoe c a n o e Downloaded From projector-manual.com Barco Manuals... -
Page 26: Adjusting The Projector Lens
Projector lens adjustment includes focus, zoom, horizontal/vertical image shift. Please refer to Chapter III on "Quick installation of the projector > Adjusting projector angle, Adjusting projector focus/zoom, Correcting keystoning caused by projection angle" for detailed instructions. Downloaded From projector-manual.com Barco Manuals... -
Page 27: Using The Remote Control
By factory default, these are: PAUSE will function normally; 1 = HDMI 1 pressing any other buttons will 2 = RGB D-15 not access the OSD Menu. 3 = RGBHV/YUV2 4 = YUV1 5 = Composite Video Downloaded From projector-manual.com Barco Manuals... - Page 28 Downloaded From projector-manual.com Barco Manuals...
-
Page 29: Osd Menu Tree
Blue Offset Input Balance White Balance Red Gain Green Gain Blue Gain 5:4 , 4:3, 16:10 Aspect Ratio 16:9, 1.88, 2.35 Letterbox, Native H Total H Start Timings H Phase V Start Auto Image Execute Downloaded From projector-manual.com Barco Manuals... - Page 30 Button 1 HDMI2 Button 2 RGB D-15(RGB-HV/ SOG)YUV1(RGB-S) Button 3 YUV2(RGBHV/YUV2) Button 4 Composite Video(Video) S-Video Button 5 RGB-S 5:4 , 4:3, 16:10 Trigger 1 16:9, 1.88, 2.35 Trigger 2 Letterbox, Native, Auto Auto Source Downloaded From projector-manual.com Barco Manuals...
-
Page 31: Osd Description
The preset value for this function is Auto. If you specify vertical refresh frequency from the input device to be between 48~62Hz, the projector will automatically lock the frequency of the input signal so that both signal input and output will be refreshed at the same Downloaded From projector-manual.com Barco Manuals... - Page 32 If you are unsure of the video standard used in your area, please contact a qualified personnel and inquire about the video standard used in your area. Downloaded From projector-manual.com Barco Manuals...
-
Page 33: Image
The following image illustrates the results of direct contrast adjustment using a random image: Lowered contrast Original image Enhanced contrast Downloaded From projector-manual.com Barco Manuals... - Page 34 Use to adjust the saturation of the projected image.If the color of the projected image seems to be overly bright and vivid, decrease color saturation; if the color seems white and washed out, increase color saturation. Reduced saturation Original image Enhanced saturation Downloaded From projector-manual.com Barco Manuals...
- Page 35 The following image illustrates the results of direct sharpness adjustment using a random image: Reduced sharpness Original image Enhancedsharpness Downloaded From projector-manual.com Barco Manuals...
- Page 36 (i.e. an image of 30IRE-window). If you notice minimal amount of red, green or blue in the gray areas, adjust the offset of the corresponding color accordingly.This function will shift the entire color spectrum for the whole image and change its brightness. Downloaded From projector-manual.com Barco Manuals...
- Page 37 Native input Output aspect ratio Output aspect ratio Output aspect ratio 16:10 16:9 Output aspect ratio Output aspect ratio Output aspect ratio Output aspect ratio 1.88 2.35 Letterbox Native Downloaded From projector-manual.com Barco Manuals...
- Page 38 The following image is an example of test image from an external signal source: Adjust image quality by changing the value of horizontal total to smoothen the image. *In order to adjust timings the pattern should be used is pixel (on/off)* Downloaded From projector-manual.com Barco Manuals...
- Page 39 (The adjustment also applies to PIP input source). This function is identical to the button on the remote control. You can simply use the hot key on the remote control to execute this function. Downloaded From projector-manual.com Barco Manuals...
-
Page 40: Layout
When you want to project PIP image, use this function to specify the image source for the PIP image. This function is identical to Input Selection; for more information, please refer to the section on Input Selection. Downloaded From projector-manual.com Barco Manuals... - Page 41 RGB D-15 – – Select YUV 1 – – – RGBHV/ YUV 2 – – – Composite Video – – S-Video – – RGB-S – – – – O mean Source Available ; — mean NA Downloaded From projector-manual.com Barco Manuals...
-
Page 42: Lamp
The projector will automatically determine the usage hours for lamp1 and lamp2 and choose the lamp with Lamp2 lower hours for the operation. Lamp1 Dual • When you require brighter image from the projector, please operate the projector with Dual lamps. Downloaded From projector-manual.com Barco Manuals... - Page 43 This function is limited to display purposes to inform the user of Lamp1's total run time. Lamp2 Run Time This function is limited to display purposes to inform the user of Lamp2's total run time. Downloaded From projector-manual.com Barco Manuals...
-
Page 44: Alignment
Installing the projector Correcting vertical keystoning caused by projection angle for more information. * The summation of the absolute value of horizontal keystone and vertical keystone is limited to less than or equal to 350. * Downloaded From projector-manual.com Barco Manuals... - Page 45 Choose this to customize the color gamut according to your preference through projector Toolset application. Lens To Midposition After series of lens shift operations, this function can be used to return the lens to the center position. Downloaded From projector-manual.com Barco Manuals...
-
Page 46: Control
By setting it to Off, the function will be disabled. You won't be able to conserve power but you can control the projector remotely over a network. Downloaded From projector-manual.com Barco Manuals... - Page 47 Bottom Right Bottom Left Start Up Logo You can use this function to have the projector display the Barco logo in the start up screen. to display the Barco logo during start up and to display a blank image. Start Up Chime Set it to On to have the projector play a sound effect during start up;...
- Page 48 You can use this function to select the language you wish for the OSD Menu to be displayed in. You can choose from the following nine languages: English, French, Spanish, German, Portuguese, Simplified Chinese, Traditional Chinese, Japanese and Korean. Downloaded From projector-manual.com Barco Manuals...
-
Page 49: Service
Note that this function will not apply to items including no signal, network, Projector control, startup Logo, language, High Altitute mode and lamp hours. *When Factory Reset is executed, all source memories created by the projector (i.e. timings files) will be erased.* Downloaded From projector-manual.com Barco Manuals... -
Page 50: Lamp And Filter Maintenance
Refer to OSD Menu description Service Lamp1, 2 Run Time. loosen the two screws 4. Grasp the metal rod on the lamp cover and pull the lamp out. Downloaded From projector-manual.com Barco Manuals... -
Page 51: Cleaning The Filter
2 screws 2. Remove the dirty filter; you can clean it directly using water. Leave it to dry before replacing it for further use. If the filter is broken, purchase a new one to replace it. Downloaded From projector-manual.com Barco Manuals... -
Page 52: Simple Troubleshooting And Definition Of The Led Indicators
The LED indicator on the The lamp or the cooling fan could be faulty. Refer to the definition of LED status. projector’s rear panel is blinking in red Downloaded From projector-manual.com Barco Manuals... -
Page 53: Led Status
Blue Green (STAND BY) (ON) (ERROR) Standby Cooling / Warm up Power on / Normal Lamp fall repeat Lamp door open repeat Fan fail repeat Over Temperature repeat System Error Downloaded From projector-manual.com Barco Manuals... -
Page 54: Projector Specifications
10 minutes under 0~10°C short operation under such temperature will not result in DMD damage. Noise level under normal < 40 dB operation Noise level under Eco mode < 37 dB Weight 28 kg Downloaded From projector-manual.com Barco Manuals... - Page 55 × × × 1080p SMPTE 274M, CEA-861-D Format 31 × × × × × 1080p 59.94 SMPTE 274M, CEA-861-D Format 16 × × × × 1080p SMPTE 274M, CEA-861-D Format 16 × × × × Downloaded From projector-manual.com Barco Manuals...
- Page 56 Projector specifications 516.76 • Downloaded From projector-manual.com Barco Manuals...
- Page 57 Downloaded From projector-manual.com Barco Manuals...
Need help?
Do you have a question about the RML W6 and is the answer not in the manual?
Questions and answers