HWM ComLog2 IS User Manual

Logger devices, installation and setup using idt

Advertisement

Quick Links

User Guide: ComLog2 IS / ISLog (logger devices).
Installation and Setup (Using HWM IDT).
(Part 1 of 2)
Warning:
This manual contains important safety and operating information.
Please read, understand, and follow the instructions in the manual
and also any safety / approvals or ATEX Safety Supplement documents
shipped with the device.
MAN-157-0001-A March 2021.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ComLog2 IS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HWM ComLog2 IS

  • Page 1 User Guide: ComLog2 IS / ISLog (logger devices). Installation and Setup (Using HWM IDT). (Part 1 of 2) Warning: This manual contains important safety and operating information. Please read, understand, and follow the instructions in the manual and also any safety / approvals or ATEX Safety Supplement documents shipped with the device.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Introduction ........................3 Documentation and Support of Product ..............3 Safety Considerations ....................4 Operating Temperature .................... 4 Overview and preparation for use ................... 5 Logger - Device Overview ..................5 Preparing a Mobile Phone (or similar device) for use with loggers ....... 5 Logger operation .......................
  • Page 3: Introduction

    OCUMENTATION AND UPPORT OF RODUCT Thank you for choosing a HWM device. We trust it will provide you with many years of service. The “ComLog2” and “ISLog” devices are general-purpose data loggers that are built and configured to suit specific applications of the device; several versions are available within each logger family.
  • Page 4: Safety Considerations

    1.2 S AFETY ONSIDERATIONS Safety Note: Before continuing, carefully read and follow the information in the “Safety Warnings and Approvals Information” document supplied with the product. This provides general safety information. The installer or maintainer must also refer to any other safety supplement documents, supplied with the intrinsically safe versions of the product.
  • Page 5: Overview And Preparation For Use

    VERVIEW AND PREPARATION FOR USE 2.1 L OGGER EVICE VERVIEW The ISLog and Comlog2 IS products are similar families of logger devices. Comlog2-IS - Automated Meter Reading applications. • ISLog - Other applications. • 2.2 P REPARING A OBILE HONE...
  • Page 6: Server Integration - Storing And Viewing Data

    Measurement data is initially stored within the loggers, until the next call-in time. The data can then be uploaded to the server using an encrypted format. Typically, the server used to receive and store the data will be a HWM DataGate server, although other servers may be used in conjunction with HWM software.
  • Page 7: Logger Security: Secure And Unprotected Modes

    Refer to the sensor user-guide or IDT app user guide to see if this is appropriate or discuss with your HWM representative regarding which viewing portal to use. 2.5 L...
  • Page 8: Activating The Logger And Communications Link

    CTIVATING THE OGGER AND OMMUNICATIONS 3.1 L OGGER ACTIVATION PROCESS IRST TIME USE When shipped from the factory, the unit is deactivated. This mode is designed to preserve its battery life whilst being shipped or in long term storage; this is often called “shipping mode”.
  • Page 9: Interfaces And Sensors Supported

    NTERFACES AND ENSORS SUPPORTED The ISLog and Comlog2 IS families of logger devices share a common plastic case. Use the key-hole shaped mounting holes to mount the logger. Holes are also provided for applications requiring anti-tamper seals to be applied.
  • Page 10: Tamper Alarm Support For Flow Sensor (Meter Pulse Detector)

    However, the installer has responsibility for confirming the settings are appropriate for use at the installed site. If you have specific requirements this can be discussed with your HWM sales representative at the time of ordering the loggers. The Configure Device pages will have considerable variation in content depending on the logger model number and the sensors being installed.
  • Page 11: Installation

    Test using signal test and call test with any access door / chamber lid open initially and then closed. (If required) transfer details of the logger to the Deployment app. • (The HWM Deployment app is then used to complete the task of selecting the site of deployment and update of the DataGate system).
  • Page 12: Installing The Logger

    Follow the additional guidance where available. 5.3 I NSTALLING THE ANTENNA AND TESTING CELLULAR COMMUNICATIONS Only use HWM-provided antenna for use with your logger, to ensure the radio interface meets approvals requirements (safety, etc). The logger family has several antenna connector options: Internal Antenna (no antenna connector fitted).
  • Page 13: Viewing Your Data

    • to the connector or antenna cable can result. For other antenna options and guidelines, refer to the documents available on the HWM support webpage: https://www.hwmglobal.com/antennas-support/ IEWING YOUR DATA The data of the connected logger can also be viewed graphically by using the IDT app to make a temporary copy of the data stored within the logger.
  • Page 14: Troubleshooting

    When returning product for investigation or repair, be sure to follow the instructions of your distributor to document why the product is being returned. If returning to HWM, this can be done by completing the on-line RMA form: https://www.hwmglobal.com/hwm-rma/ Prior to shipping, put the equipment into Shipping mode (refer to the IDT app user- guide for instructions).
  • Page 15: Connector Information

    ONNECTOR INFORMATION The logger is available with many connection options. Discuss your specific needs with your HWM representative to confirm availability. This section provides additional information for connection options that are widely used. Warning: This equipment must be installed by a person who is competent to make any required electrical connections in a manner suitable for the installation site.
  • Page 16 All images, text and designs are protected by international and UK copywrite law and remain the property of HWM-Water. It is against the law to copy or use any of the content from the HWM website or literature without the written consent of HWM-Water.

This manual is also suitable for:

Islog

Table of Contents