Subscribe to Our Youtube Channel
Related Manuals for SUMERAIN S6111CI
Summary of Contents for SUMERAIN S6111CI
- Page 1 MODEL: S6111XI Version: V1.1 INSTALLATION GUIDE WALL MOUNT POT FILLER MODEL FINISH S6111CI CHROME S6111NI BRUSHED NICKEL S6111OI Oil-Rubbed Bronze S6111GI Brushed Gold S6111DI Matte Black HOT LINE: +1-866-203-0866...
-
Page 2: Before Proceeding
Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. -
Page 3: Limited Lifetime Consumer Warranty
This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship as follows: SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. - Page 4 FUNCTIONS AND SPECIFICATION Inspire the master chef within: the stylish Pot Filler is convenient and practical. Able to reach all stove burners for filling pots, the folding arm retracts completely when not in use. ● 4.0 gpm @ 60 PSI, 15.1 L/min @ 414 kPa. ●...
- Page 5 DEMENSION Front view Left view...
-
Page 6: Installation Steps
Flange trim SUS304 PEC61110SB Opening circlip PRW22178XX O-Ring POR42020XX O-Ring POR21028XX Mounting screw SUS304 PSC00002XX Sway nipple SUS304 PCN61110XX Wall Flange SUS304 PEC61111XX Washer PRW25221XX If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com. -
Page 7: Installation
4. INSTALLATION 4.1 Apply sealant tape to the NPSM 1/2 to NPT1/2 nipple (NPT1/2 side). 4.2 Connect to 1/2" NPT supply line by Allen key. The nipple should extend Min 9/16”(15mm) and Max 1-3/16”(30mm) past the finished wall surface... - Page 8 Place wall flange onto the faucet as shown. Thread faucet provided onto pipe. 4.4 Mark the screw holes in the flange. Unthread the faucet the nipple.
- Page 9 4.5 Drill 1/8" (3 mm) holes where marked. If using the anchors, drill 3/16" (4.5 mm) holes. 4.6 Seal the backside of wall flange with waterproof sealant...
- Page 10 4.7 Wrap Teflon tape around nipple threads (NPSM 1/2). Install the wall flange using the 4 screws (and anchors if required) provided. 4.8 Place flange trim onto the faucet as shown. Thread faucet onto nipple. Tighten securely, but do not over tighten.
- Page 11 4.9 Tighten set screw in flange. Slide flange trim over the wall flange.
- Page 12 4.10 Remove aerator and turn faucet handles to the full on position. Turn on cold water supplies and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. 6. INSPECTION 6.1 Turn on cold water supply and check all connection for ensuring no leaking anywhere. INSTALL FINISH...
- Page 13 Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG Factory Address: Floor 3th,No.2 ZhongXing Road,ShuiNuan City Industrial Zone,Shuikou town, Kaiping City,...
Need help?
Do you have a question about the S6111CI and is the answer not in the manual?
Questions and answers