Related Manuals for SUMERAIN S1408CW
Summary of Contents for SUMERAIN S1408CW
- Page 1 Version: 1.2 WIDESPREAD BATHROOM SINK FAUCET MODEL FINISH S1408CW Chrome S1408NW Brushed Nickel S1408OW Oil Rubbed Bronze S1408DW Matte Black S1408BGW Brushed Gold...
- Page 2 Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions.
- Page 3 If a defect is found in normal residential use, SUMERAIN will, at its election, repair, provide a replacement part or product, or make appropriate adjustment.
- Page 4 Function Bathroom Sink Faucets Feature Waterfall Style Contemporary Finish Chrome/Brushed Nickel/Matte Black Three Holes Installation Holes Number of Handles Two knobs 130mm [5-7/64 Inch] Spout total Height 120mm [4-23/32 Inch] Spout Reach Spout Width 80mm [3-9/64 Inch] Spout Height 88mm [3-15/32 Inch] Max deck thickness 32mm...
- Page 5 FRONT VIEW OF FAUCET SIDE VIEW OF FAUCET...
-
Page 6: Before Proceeding
1PCS Screen washer 1PCS 1408013 1408014 1PCS Set screw 2PCS 1408015 1408016 Screw cover 2PCS Allen wrench 1PCS 1408017 1408018 G1/2’’ hose 2PCS 1408019 If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com... - Page 7 4. INSTALLATION HOLES INSPECTION Verify that the hole sizes and positions in the wall are correct, the diameter of mounting hole recommend 1-1/4” (32mm) and maximum 1-3/8” (35mm), the max thickness of deck should be 1-3/4” (45mm).
-
Page 8: Installation
5. INSTALLATION 5.1 Turn on your shut-off valve for cleaning the hot and cold water supply pipe before connect to the faucet, allow the water flush 3~5 minutes to flush out dirt and debris. Shut off the water supply again after done. 5.2 Attached the flow restrictor to shank of spout. - Page 9 5.3 Position spout onto the hole of mounting surface, attach rubber washer on spout shank and fasten with spout shank locknut by wrench from underneath. 5.4 Disassemble hot and cold water valve assembly to prepare for next step’s installation. Take out the screws cover from knob and loose the inside set screw by Allen wrench anticlockwise, disassemble the knob from the valve assembly.
- Page 10 5.5 Place the valve body onto mounting surface, attach the rubber washer and locknut from underneath of mounting surface, attached the O-ring with the escutcheon, Then reposition escutcheons as necessary to a desired height. 5.6 Fasten the knobs with set screws by Allen Key and repeat the same procedure for the right cold valve assembly.
- Page 11 5.6 Attach the washer into the tee for water leak proof. 5.7 Screw on tee onto the spout shank...
- Page 12 5.8 Connecting the cold water valve body and hot water valve body to tee with flexible hoses. 5.9 Connect hot valve body’s inlet connector and cold water valve inlet connector to stop valve separately with flexible hose. The water inlet connecting of hot and cold Valve body is G1/2” [1/2 BSPP], US, CA customers may require NPT cover to BSPP adapter for connecting.
- Page 13 6. INSPECTION 6.1 Turn on hold and cold water supply and check all connection for ensuring no leaking anywhere. INSTALL FINISH SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 14 Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG...
Need help?
Do you have a question about the S1408CW and is the answer not in the manual?
Questions and answers