Related Manuals for SUMERAIN S3221XI
Summary of Contents for SUMERAIN S3221XI
- Page 1 MODEL: S3221XI Version: 1.2 INSTALLATION GUIDE Shower Only Faucet with Rough-in Valve MODEL FINISH S3221CI Chrome S3221NI Brushed Nickel S3221DI Matte Black S3221OI HOT LINE:+1-866-203-0866...
-
Page 2: Before Proceeding
THANK YOU Dear Valued Customer, Thank you for choosing SUMERAIN products. We would like to take this opportunity to express our sincere gratitude for your recent purchase. We hope you are completely satisfied with your new product. Rest assured, we meticulously engineer all SUMERAIN products and put them through rigorous factory tests to ensure their prolonged, trouble-free use under normal conditions. -
Page 3: Limited Lifetime Consumer Warranty
LENGTH OF WARRANTY As stated in the following, any replacement or repaired parts of the product will be covered for the duration of this warranty, which SUMERAIN provides for a period of 1 year from the original date of purchase. -
Page 4: Functions And Specifications
FUNCTIONS AND SPECIFICATIONS Faucet Type Shower Faucet Theme Modern, Contemporary Finish Chrome / Brushed Nickel / Matte Black / ORB Mounting Type Wall Mounted Number of Handles Handles Material Metal Handle Style Lever Shower Arm Reach 5-13/16 in. [148 mm] Showerhead Dimension 7-7/8 in. - Page 5 DIMENSION FRONT VIEW...
- Page 6 SIDE VIEW...
-
Page 7: Installation Steps
3. CHECK THE COMPONENTS OF THE BOX Upon opening the box, verify the presence of the following items. If any of these items are missing, please contact SUMERAIN consumer service via email: supports@sumerain.com. CODE ITEM NAME... - Page 8 4. PREPARATION Attention: To ensure proper shower function, the shower must be installed, rinsed, and checked in compliance with all applicable regulations! The dimensions of the shower setup must be determined individually. For the operating pressure at the control valve: Maximum: 1Mpa Recommended operating pressure: 3 bar The maximum hot water temperature should be 60 degrees Celsius (140 degrees Fahrenheit).
- Page 9 Secure the concealed box assembly to the mounting rack using screws and anchors. 6. VALVE TRIM INSTALLATION 6.1 Before connecting the hot and cold water supply pipes to the valve body, turn on your shut-off valve to clean them. Allow the water to to flush out any dirt and debris for 3 to 5 minutes .
- Page 10 6.2 Apply Teflon tape to the thread of the pipe inlet, then connect the pipe inlet to the valve inlet using an elbow fitting (hot on the left, cold on the right). The mixer valve has a connecting thread for the hot and cold water inlets of NPT 1/2” Connect the valve outlet using an elbow fitting:...
- Page 11 6.3 Remove the valve sleeve using a Phillips screwdriver. Turn on both the hot and cold water supplies and check all connections for leaks. If there are no leaks, please turn off both your hot and cold water supplies again. 6.4 Drill the mounting holes precisely according to the positions of the mixer valve and elbow, then finish the wall.
- Page 12 6.5 Remove the valve sleeve from valve assembly. 6.6 Attach the escutcheon over the valve body.
- Page 13 6.7 Seal the wall around the escutcheon with waterproof sealant 6.8 Attach handle onto the valve stem and tighten set screws by the Allen wrench that is provided. Please don’t over tighten. Finally press-in the screw cover.
- Page 14 6.9 Valve trim installation is complete. 7. SHOWERHEAD INSTALLATION 7.1 Attach the shower arm escutcheon to the shower arm, then apply Teflon tape to the threaded end of the shower arm.Then, secure the shower arm into the pipe elbow inside the wall by rotating it clockwise. Standard thread of Shower arm inlet: NPT1/2 (US, CA) G1/2”...
- Page 15 7.2 Seal the wall around the shower arm escutcheon with waterproof sealant.
- Page 16 7.3 Insert the screen washer into the connector of the showerhead, then secure the showerhead onto the shower arm by rotating it clockwise by hand. Missing the screen washer might lead to the shower not functioning properly. 8. INSPECTION Turn on both the hot and cold water supply, then check all connections to ensure there are no leaks anywhere. INSTALLATION COMPLETED...
- Page 17 Note: if the surface is already damaged, the application of cleaning materials might exacerbate the damage. Components with damaged surfaces need to be replaced to avoid potential injuries. Note that any damage resulting from improper treatment is not covered by the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: Room 1018, Hollywood Plaza,610 Nathan Road, Mong Kok, Kowloon, Hong Kong.
Need help?
Do you have a question about the S3221XI and is the answer not in the manual?
Questions and answers