Part Names, Functions And Displays; Tuner Display - Denon D-F10 Manual

[5] PART NAMES, FUNCTIONS AND DISPLAYS
REMOTE SENSOR
When operating the remote control unit, point it at
this sensor.
SYSTEM POWER switch
(This turns the power for the entire system on and
off.)
Press this once to turn the power on, then press again
to set the power to the standby mode.
Power indicator
This lights when the power cord is plugged into a
power outlet, and flashes for 5 seconds after the
system power is turned on.
PHONES (headphones jack}
Plug the headphones into this jack.
No sound is produced from the speakers when
headphones are plugged in.
BALANCE control
Use this to adjust the balance of the volume between
the left and right channels. When set at the center
position, the volume is the same for the left and right
channels.
CLOCK/DISPLAY selector button
This button is used to switch the display between the
reception frequency and the clock.
TUNING UP and DOWN buttons
These buttons are used to select AM and FM stations
and to set the clock and timer.
POWER switch
Press this button once to turn the tuner's power on,
then press again to set the tuner to the standby
mode. in the standby mode, "OFF" appears on the
display.
TIMER/ TIMER STANDBY button
Press this when setting the timer and to turn the timer
on so that it operates at the set times.
When the button is pressed after the timer has been
set, the timer standby mark (" (© _ ") appears on the
display. Press again to turn the mark off.
The timer will not operate when the" (& " mark is
off.
©
VOLUME control
Use this to adjust the overall volume.
The volume increases when the control is turned
clockwise ( } and decreases when it is turned
counterclockwise ( () ).
FUNCTION (input) selector button
Use this to select the input (function).
The input changes in the following order each time
this button is pressed: CD, TAPE, TUNER, PHONO.
MD/AUX. (The function changes automatically when
the system's CD player or cassette deck is played or
when a preset channel is recatled on the tuner.)
BASS control
Use this to adjust the volume of the low frequencies.
TREBLE control
Use this to adjust the volume of the high frequencies.
Function indicators
These light to indicate the currently selected function.
BAND (AM/FM) selector button
The band switches between AM and FM each time
this button is pressed.
MONO/STEREO selector button
AUTO mode: Use this mode to receive programs in
stereo.
The sound and the indicators on the
display automatically switch between
monaural ("MONO") and stereo
("STEREO") according to whether the
program is being broadcast in monau-
ral or stereo.
MONO mode: Use this mode to receive programs in
monaural, regardless of whether they
are being broadcast in monaural or
stereo.
Set this mode if there is much noise or
if the signals are weak when receiving
stereo programs (when "AUTO" is lit).
MEMO ENT/NEXT button
This button is used to preset AM and FM stations and
when setting the timer.
Display
TUNER DISPLAY
The timer will ope-
rate when this is lit.
This indicates the
number of the preset
channel.
This lights when the display is set to the
clock mode. :
The reception band, reception frequency, time
and timer settings are displayed here.
Displays the timer and RDS data.
This lights when a
station is tuned in
properly.
This flashes for approximately 10
seconds when the MEMO button is
pressed while presetting stations.
These light when set-
ting the timer.
"TIMER" lights when
the timer is set.
This lights when the
sleep timer is opera-
ting.
These display the reception mode.
STEREO: This lights when a stereo program is
received in the AUTO mode.
: This lights when a monaural pro-
gram is received in the AUTO mode
and when the MONO/STEREO but-
ton is pressed, setting the monaural
mode.
: This lights when the MONO/STEREO
button is pressed, setting the auto
mode.
This lights when in
the standby mode.
MONO
AUTO
e@ RDS (Radio Data System)
When the ROS button is pressed, a station is searched
for and automatically tuned in, the "RDS" indicator
lights and the station's name is displayed on the
frequency display.
@ PTY (Program Type)
This indicator lights when the type of RDS program is
specified.
e@ TP (Traffic Program)
received.
@ PS (Program Service name)
This lights when the station name is displayed.
NOTE:
© The timer standby mark (" © ") does not light if the
current time and the timer have not been set.
"TP" lights when an RDS traffic information station is
q)
m
2
mi
Ps)
>
-
2)
m
Q
=
)
2
Sa aa a a a PS () | 1] HER