Subscribe to Our Youtube Channel
Related Manuals for Clarke DEVIL 4000
Summary of Contents for Clarke DEVIL 4000
- Page 1 PROPANE GAS HEATER MODEL NO: DEVIL 4000 PART NO: 6926150 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS DL1123- Rev 7...
-
Page 2: Function And Operating Parameters
INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. -
Page 3: Safety Information
SAFETY INFORMATION Read, and make sure you fully understand the following precautions and the hazards associated with this type of equipment. 1. ONLY use with the voltage specified and ensure the heater is properly earthed. 2. Use only the hose and factory preset regulator provided with the heater. 3. -
Page 4: Safety Symbols
20. Keep the heater away from strong drafts, water spray, rain or dripping water. 21. DO NOT leave the heater unattended. 22. NEVER move, handle or service a hot, operating or plugged-in heater. 23. To prevent injury wear gloves when handling the heater. 24. -
Page 5: General Precautions
GENERAL PRECAUTIONS Even though this heater operates very close to 100 percent combustion efficiency, it still produces small amounts of carbon monoxide. • Carbon Monoxide (CO) is toxic. • Pregnant women, persons with a heart or lung condition, anaemia or under the influence of alcohol, or those at high altitude, are more likely to be effected by Carbon Monoxide. -
Page 6: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply through an approved BS1363 plug fitted with a BS1362 13 amp fuse. If the plug has to be changed because of damage, it must be removed and a replacement fitted, following the wiring instructions shown below. -
Page 7: Propane Gas Supply
PROPANE GAS SUPPLY WARNING: THE FITTING AND CHANGING OF THE GAS CYLINDERS MUST BE CARRIED OUT IN A FLAME FREE ATMOSPHERE. WARNING: YOU SHOULD ONLY USE PROPANE GAS CYLINDERS AVAILABLE FROM BUILDERS MERCHANTS OR GAS SUPPLIERS. This portable, direct-fired gas heater is designed to give safe, efficient and reliable operation, and is for use with propane gas only. - Page 8 ASSEMBLY 1. Stand the heater on end as 2. Attach the lower frame and shown. We recommend the help secure using six of the machine of an assistant to lift and steady screws provided. the heater during assembly. 3. Attach the handle to the lower 4.
-
Page 9: Size And Capacity Of Propane Cylinders
PREPARATION LOCATION • Position the heater at a safe distance from combustible materials. • This heater must not be placed on wooden floors or other combustible materials. • When used, the heater should rest on suitable insulating material at least 1 inch thick and extending 3 ft or more beyond the heater in all directions. -
Page 10: Heater Start Up
OPERATING INSTRUCTIONS WARNING: BEFORE STARTING THE HEATER, YOU MUST ENSURE THAT THE MINIMUM VENTILATION REQUIREMENTS ARE OBSERVED TO AVOID THE RISK OF CARBON MONOXIDE POISONING. HEATER START UP 1. Open the propane supply valve on the propane tank(s) slowly. • If not opened slowly, the excess-flow check valve on the propane tank will stop the gas flow. -
Page 11: Maintenance, Storage And Servicing
MAINTENANCE, STORAGE AND SERVICING WARNING: TO PREVENT PERSONAL INJURY, UNPLUG THE HEATER FROM THE MAINS SUPPLY BEFORE SERVICING. MAINTENANCE AND STORAGE The heater should be inspected at least annually by a qualified person. 2. Before each use, check the soft “0” ring seat at the bullnose of the POL fitting. -
Page 12: Specifications
SPECIFICATIONS Model DEVIL 4000 Gas Type Propane BTU Rating 400,000 Maximum Pressure Bottle Pressure Minimum Pressure 1.4 Bar Regulator Output 20 PSIG (0.14MPa) Electrical Input 220-240V, 50Hz Ignition Direct Spark Primary Flame Control Solid State 10-15 Sec timing Operating Temperature Range... -
Page 13: Exploded View
EXPLODED VIEW Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Parts List
PARTS LIST Front Guard Control Box End Panel Locknut Thermostat Mounting Bracket Machine Screw Thermostat Assembly Middle Cylinder Orifice (2.35 mm port) Outer Shell Fuel Tube Assembly Grille Inlet Male Fitting, Conn. 1/4 MPT x 1/2 Machine Screw TEE 1/4 N PT, Female Fitting Machine Screw Fitting, Plug 1/4 MPT Burner Outer Plate... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the DEVIL 4000 and is the answer not in the manual?
Questions and answers