CABLE CONNECTORS Product Overview Cabling must have a male XLR connector on one end and a female XLR connector on the other end. DMX connector configuration GROUND caution:Do not allow contact between the ground and the fixture’s chassis ground. Grounding the ground can cause a ground loop, and your fixture may perform erratically.
Mechanical Specification RDM---Remote Device Management RDM is a wild version of the DMX512-A protocol, allowing dimming stations and other control devices to be discovered through a DMX512 network, and then configuring, status monitoring, and managing intermediate and line end devices. It allows two-way communication between the lighting device or system controller and the connected RDM compatible device through the standard DMX.
Page 4
INFORMATION-In this menu, you can learn about the information of RDM, software and hardware of the light. 1.Press “ENTER” and then press “UP” or “DOWN” to “INFORMATION”. Packaging: Thanks for your purchasing the ARC BAR PRO STROBE. All the lights have 2.Press “ENTER”...
Page 5
Features Mounting ● Light Source: 360pcs white led,192pcs RGB 5050 1W LED When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit ● Beam angle: 90° must be secured with a secondary safety attach-ment, e.g.
Displayer introduction ① ② ③ temp:043 ④ ADDRESS ⑤ Key lock open MENU DOWN ENTER 1. DMX means the light is in the DMX mode.Similarly,SLAVE means the light is in the SLAVE mode. 2. The color of the point shows the condition of signal transmission. Green represents the good condition, while red represents the signal is interrupted.
DMX MODE-In this menu,you can connect several pieces of lights with DMX cable and control them with the control console. Programme Menu Press ”ENTER” and then press “UP” or “DOWN” to ”Address” or “DMX Channel” and press “ENTER”. 1) “XXX” will be showed in “Address”, "XXX” means the Address 001-512. You can press “UP” or “DOWN”to select the address you desired.
DMX-512 addressing with ID address 1. Follow instructions 1 for DMX 512 addressing. 2. Activate ID addressing in each fixture by setting panel function “ID ON/OFF” to ON. “Settings” to “ID ON/OFF” to “ON” For every DMX 512 starting address the user can set 66 separate ID addresses.
Page 19
DMX MODE-In this menu,you can connect several pieces of lights with DMX cable and control them with the control console. Programme Menu Press ”ENTER” and then press “UP” or “DOWN” to ”Address” or “DMX Channel” and press “ENTER”. 1) “XXX” will be showed in “Address”, "XXX” means the Address 001-512. You can press “UP” or “DOWN”to select the address you desired.
Page 20
INFORMATION-In this menu, you can learn about the information of RDM, software and hardware of the light. 1.Press “ENTER” and then press “UP” or “DOWN” to “INFORMATION”. 2.Press “ENTER” and you can see 3 items as below: 1) RDM - It shows RDM information. 2) Hardware - It shows the Hardware information.
Page 21
Features Mounting ● Light Source: 360pcs white led,192pcs RGB 5050 1W LED When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit ● Beam angle: 90° must be secured with a secondary safety attach-ment, e.g.
Page 22
CABLE CONNECTORS Cabling must have a male XLR connector on one end and a female XLR connector on the other end. DMX connector configuration GROUND caution:Do not allow contact between the ground and the fixture’s chassis ground. Grounding the ground can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify positive pole and to make sure the pins are not grounded or shorted to the shield or each other.
Page 23
Mechanical Specification RDM---Remote Device Management RDM is a wild version of the DMX512-A protocol, allowing dimming stations and other control devices to be discovered through a DMX512 network, and then configuring, status monitoring, and managing intermediate and line end devices. It allows two-way communication between the lighting device or system controller and the connected RDM compatible device through the standard DMX.
Page 24
IMPORTER B&K LUMITEC ZI – 2 Rue Alfred Kastler – 67850 Herrlisheim – France www.bklumitec.com...