Makita VC011G Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Vacuum Cleaner
  5. VC011G
  6. Instruction manual
Makita VC011G Instruction Manual

Makita VC011G Instruction Manual

Cordless backpack vacuum cleaner
Hide thumbs Also See for VC011G:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
Cordless Backpack Vacuum Cleaner
VC011G
Read before use.

Advertisement

Table of Contents
loading

Related Manuals for Makita VC011G

Summary of Contents for Makita VC011G

  • Page 1 INSTRUCTION MANUAL Cordless Backpack Vacuum Cleaner VC011G Read before use.

  • Page 2: Specifications

    • If the device is to be stored unused for a long period, the batteries should be removed. • The power terminals must not be short-circuited. SPECIFICATIONS Model: VC011G Capacity Filter bag 6.0 L Dust bag 5.5 L Maximum air volume 2.4 m...

  • Page 3: Safety Warnings

    Symbols WARNING: Wear ear protection. WARNING: The noise emission during actual The followings show the symbols which may be used use of the power tool can differ from the declared for the equipment. Be sure that you understand their value(s) depending on the ways in which the meaning before use.
  • Page 4 Do not use the cleaner without the filter. 21. Do not attempt to clean the exterior or interior Replace a damaged filter immediately. with benzine, thinner or cleaning chemicals. Do not attempt to pick up flammable materials, Cracks and discoloration may be caused. fireworks, lighted cigarettes, hot ashes, hot 22.
  • Page 5 Do not expose battery cartridge to water causing fires, personal injury and damage. It will or rain. also void the Makita warranty for the Makita tool and A battery short can cause a large current charger. flow, overheating, possible burns and even a breakdown.

  • Page 6: Functional Description

    FUNCTIONAL CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, DESCRIPTION it may accidentally fall out of the appliance, causing injury to you or someone around you. CAUTION: Do not install the battery cartridge CAUTION: Always be sure that the appliance forcibly.
  • Page 7 Indicator lamps Remaining Battery indicator status Remaining capacity battery capacity Blinking Lighted Blinking 50% to 100% 75% to 100% 50% to 75% 20% to 50% 25% to 50% 0% to 20% 0% to 25% Charge the Charge the battery. battery The battery may have malfunctioned.

  • Page 8: Adjusting Belts

    Let the appliance and battery(ies) cool down. If no improvement can be found by restoring protection system, then contact your local Makita Service Center. Switch box position The switch box can be hooked on either side of the lower belt.

  • Page 9: Led Light

    Carrying hook NOTE: You can change the suction power before turning on the cleaner. Always grab the carrying hook when handling the vac- NOTE: The cleaner starts the operation with the uum cleaner body. same suction power as the last operation. NOTE: If you remove the battery immediately after turning off the appliance, while the motor is rotating, the cleaner may not start the operation with the same...
  • Page 10 The loops on the lower belt can be used for carrying ASSEMBLY nozzles as illustrated. CAUTION: Always be sure that the appliance is switched off and the battery cartridge is removed before carrying out any work on the appliance. Assembling hose Insert the hose cuff into the vacuum cleaner body and turn it clockwise.
  • Page 11 When using floor/carpet switching t-nozzle, you can For the snap-on type bent pipe assembly To attach, insert the hose end into the bent pipe assem- change the mode depending on the place. bly. Make sure that the tabs on the hose end snap into —...
  • Page 12 The length of the wand can be adjusted. The length of the wand can be adjusted. With pressing the slide button, adjust the wand length. Loosen the ring on the wand and adjust the wand The length is locked when releasing the slide button. length.

  • Page 13: Connecting The Tool

    For the two aluminum straight pipes Supplied Hose end type Action Shoulder the vacuum cleaner body then twist and insert hose the pipes. To disconnect, twist and extract it. diameter ø38 mm Replace the hose with the one for dust extraction (ø28 mm, with front cuff).
  • Page 14 When using ø38 mm hose with front When the filter bag is already full, NOTICE: cuff 38 replace with new one. When the dust bag is already full, empty it. Continuous use with the filter Twist and insert the joint or the front cuff to the bag/dust bag full results in reduced suction power.
  • Page 15 Unlock the lever and open the front cover. When using the dust bag, insert the brim of the dust bag into the slit. Fig.31 Fig.29 ► 1 . Slit 2. Brim 3. Dust bag ► 1 . Lever 2. Front cover Align the hole of the filter bag with the hose cuff Insert the filter bag into the slit on the upper side of and push the cardboard portion to the end.

  • Page 16: Harness Cover

    Harness cover OPERATION Optional accessory WARNING: Operators shall be adequately When using the harness cover, follow the procedure instructed on the use of the vacuum cleaner. below to attach it. WARNING: This vacuum cleaner is not suit- NOTE: When installing the harness cover, do not able for picking up hazardous dust.

  • Page 17: Maintenance

    Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Cleaning the HEPA filter CAUTION:...

  • Page 18: Cleaning The Sponge Filter

    Open the front cover and take out the filter bag/ To install the filter, insert the side without the dust bag. Release the hook on the filter and remove it hooks into the groove then push in the filter until the from the vacuum cleaner body.

  • Page 19: Cleaning The Dust Bag

    Wipe and shake dust off the sponge filters by Cleaning the room for filter bag/dust bag hand. When the sponge filters are clogged, wash them in soapy water. This appliance is equipped with a dust beating system. As you walk while carrying the cleaner, springs underneath the board vibrate the board and shake the dust off the filter bag/dust bag.
  • Page 20 The board is supported by three springs. CYCLONE ATTACHMENT If the springs came off from the projections, reattach them as illustrated. Optional accessory NOTE: When using the cyclone attachment with this appliance, the bent pipe is also required. Fig.50 ► 1 . Cyclone attachment Fig.48 ► 1 .
  • Page 21 Disposing of dust Cleaning When the dust case becomes dirty or the mesh filter is When dust has accumulated up to the full line of the dust case, follow the procedure below and dispose of clogged, remove and wash them with water. (Refer to the dust.

  • Page 22: Optional Accessories

    ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita prod- uct specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 24 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885A49-221 20230731...

This manual is also suitable for:

Vc011gz01

Table of Contents