Advertisement
ver pit VCR Plus+ Setup
Easy Taping.
In order for the VCR to read the VCR Plus+ code, some set up is required. A Guide (VCR Plus+) channel
number is assigned to each local broadcast and cable station. Because this number sometimes differs from
the channel your TV receives the station on, it is necessary to program the VCR with local channel information.
OOOO
ADD/
DELETE
ye
=
o]
ioj
jO
Channel Setup Preparations
NOTE: Complete the steps on this page if your
VCR hook-up resembles "2" on page 12.
Prepare a list like the example below.
This list will help you smoothly enter the
information needed in step "4" at right.
You will need the following to complete the list:
E A line up of normal and/or cable stations you
receive along with the channel numbers your
TV receives them on. A cable channel line-up
chart is supplied by your cable company.
MW A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in TV Guide and the TV listings found
in selected newspapers.
{1 Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2 In the middle column, fill in each station's
assigned Guide (VCR Plus+) number found in
TV Guide, newspapers, etc.
3 In the right column, fill in the channel number
that your TV receives the station on from your
channel line-up.
EXAMPLE ONLY
your TV
Station Name
channel no. | station on
ces
| oa [07
E
o
EN
EAS SE
ae
o
ee
32
VCR Plus+ Channel Setup
For Connection Type 2 (on page 12) only
+ Before you begin, complete the Channel Setup
Preparations below left.
Important Note:
If your VCR connection type changes from 1 to 2, perform "To
setup the VCR in case a cable box or DSS receiver was installed or
replaced" section on page 17 before proceeding with these steps.
SET
¡> KEY
:MENU
KEY
7
* Push MENU to
43
O
` display the menu.
~
a
' Push AV toselect
LED
(> "SET UP CHANNEL,"
©
and then push P to display
- "the "SET UP CHANNEL" screen.
---
SET
UP CHANNEL
---
©
Za
Push AY to select
As
"VCR Plus+ CH SET
| antenna system : catv
©
á UP," and then push >
CABLE/DSS BOX SET UP
to display the "VCR
S
:> KEY
screen.
END
:MENU KEY
SET UP VCA
EF CLOCK
ID 1OMA/ LANGUE: ENGL1 SH
SELECT :4 Y KEY
IMPORTANT NOTE:
For step "4," use the list you prepared. You may leave lines
blank if you don't receive that station, or if the GUIDE CH
number and the CATV (or TV) CH numbers are the same.
- Push > to move
VCR Plus+ CH SET UP
n s
es
EY 4
> the shaded area to
GUIDE CH
CATV CH
.
v
the right side.
> y
f
02
SELECT: 4 Y KEY
Y
"MENU KEY
Then, push ÁY to change CATV
or TV CH
number.
VCA Plus+
CH SET UP
Next, push to set the number.
GUIDE CH
CATV CH
Now, push AY to continue.
> 01
=
02
--
Repeat this operation until the list is
complete.
SELECT:á
Y KEY
i
KEY
¡MENU
KEY
To Make Corrections
Push AV and P to select the incorrect CATV or TV CH number.
Then, push AY to change, or ADD/DLT to delete the channel.
© o
+ Make each entry within 5 minutes or the VCR will leave this mode. .
* Once local channels have been programmed, they will stay in
memory, even in the case of a power failure.
Push MENU three times
to exit the VCR Plus+ CH
SET UP mode.
VCR Plus+C* and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ system is manufactured
under license from Gemstar Development Corporation.
Advertisement
