Advertisement
This tustration shows
how the picture
output from the OUTPUT '3. jack is
viewed on monitor.)
Using monitor [1]
cococo
ioggodo
0 Fooooga
Using monitor [)
Note on adjusting the volume of monitor it!
Noise may be heard while the volume of monitor
This beng adjusted with the WA buttons.
Do nat
adjust the volume while recording the picture and
sound recorded on monitor.1 . or the noise also
willbe recorded
Noise is not heard when monitor
2,18 selected
Using monitor {2}
noone
2
Hono
_ ©
|||
First decide which picture is to be watched
on which monitor.
1 Turn on the power to the monitor, the
video/audio
selector, and the desired
video equipment.
2 MONITOR selectors
Press the number [1}—{6) assigned for
the jack where the desired video
equipment is connected.
The pressed
button lights up.
3 INPUT/OUTPUT selector
Select the picture to be monitored: the
picture input to the INPUT jacks chosen
in step 2, or that output trom the
OUTPUT jacks.
The bution
corresponding to the selected picture
lights up
A Start playback or recording on the
video equipment.
When using an AV processor
To monitor the picture being edited with an AV
processor, select the output jacks where the
recording VTR is connected with the choice of
OUTPUT for the INPUT/OUTPUT selector. or
select the input jacks with the choice ot INPUT for
the INPUT/OUTPUT selector.
To monitor the
picture to which special effects are not provided
by the AV processor, press VIDEO of the
PROCESSOR
PASS buttons.
Do not press the
PROCESSOR
PASS button during editing, or the
piclure without the special effects will be recorded
Note on the audio level
This video/audio selector does not include an
amplitier.
if the monitor {1] vaiume does not
increase to the desired levei with the ¥.& buttons,
adjust the volume on the connected amplifier or
monitor
Buttons and selectors effective during
monitoring the picture
When using
the monitor connected to the
MONITOR|1j
jacks, the following butions and
selectors of this unit function during monitoring
the picture
MUTING buttons (VIDEO, AUDIO):
Mutes
picture and sound respectively.
AUDIO MODE selectors:
Swiiches the sound to
stereo, monaural. left channel only, or nght
channel only.
If the left only of the right only is
selected with a stereo monitor, the left or right
sound will be heard trom both speakers.
VA buttons:
Adjusts the volume.
The above buttons and selectors adjust only the
picture dispiayed on the monitor and the sound
heard trom the speakers: thus the recorded
signals are not allected even if they are operated
during editing.
1-9. EDITING
Tt
Mode indicators
ABC
— 1 r—*
=~
to a desired mode {A. B, C)
gcaqg0
lB The shadowed buttons do nol tunction in mode A
VIR3
inpuT@
ouTPuTEy
ouTPuTG}
inPuT Et
Three Output Modes for
Editing
You can select one ot the three output
modes: A, B, and C—whichever one Is
most appropriate for the use of this unit
Select the desired made with the OUTPUT
MODE switch on the front panel.
For simple and secure editing
~Mode A
Select mode A for simple and secure
editing, such as recording the playback
picture from a single VTR on another VTR.
Video equipment is connected to the input
and output jacks of the same number, and
the video equipment can easily be
identified with the jack number during
editing. This video/audio selector has 6
sets of input/output jacks, and 3 different
kind of editing can be performed at the
same time. Recording and playback cannot
be made simultaneously on the equipment
connected to the input and output jacks of
the same number.
In this mode, the inpul/
output system where video and audio
signals go out and come in in cycle, as
shown in the diagram to the left, is not
possible.
40
Advertisement
