Advertisement
USB Charging Cable
20030405-2 White
TIPS
NOT ALL TIPS INCLUDED IN ALL MODELS
*Replace Every 3 months
**Replace Every 6 months
Replacement tips/attachments may be purchased online at www.waterpik.com (US) www.waterpik.ca (Canada), or by phone from Water Pik, Inc. at 1-800-525-2774 (US) or 1-888-226-3042 (Canada).
Charge unit for approximately 4 hours prior to first use. Plug the user supplied USB wall charger into a wall outlet and connect the USB charging cable to the unit (see images). Refer to the IMPORTANT SAFEGUARDS section for required USB wall charger specifications. Ensure contacts on BOTH the cord and the unit are clean and dry, and the reservoir is empty and collapsed. The LED light will emit a slow glow on/off when unit is charging. Once the unit is fully charged and the charger is connected the LED will remain on until the charger is disconnected. A full charge will last up to 4 weeks of typical use. When the batteries are in need of charging (approximately 30% charge left) the charge indicator light emit a rapid triple blink during and after use to indicate that you should recharge the unit.
USB wall charger is not standard accessory with this appliance.
A complete recharge will take 3-4 hours. If you use your Water Flosser once a day or less, it is recommended you charge every 3-4 weeks. If you use it twice a day or more, charge more frequently.
Put the protective charging port cover back into place before use. The charging port cover should only be removed for charging.
Remove the charging cable from the unit and replace charging port cover prior to filling reservoir and product use. Pull down on reservoir to open. Unit will "click" into place when fully extended. Lift flip top on reservoir and fill the reservoir with lukewarm water.
Collapse by pushing reservoir up. Reservoir will "click" into place when fully closed.
Insert tip at the top of the unit. Press firmly until the tip clicks into place. To remove the tip from the unit, press the tip eject button and pull tip from the unit.
Do not press tip eject button while unit is running.
Lean low over sink and place tip in mouth. Aim the tip toward gumline, and turn the unit ON.
For best results, start with the back teeth and work toward the front teeth. Glide tip along gumline and pause briefly between teeth. Continue until you have cleaned the inside and outside of both the upper and lower teeth.
Direct the jet stream at a 90-degree angle to your gumline. Slightly close lips to avoid splashing but allow water to flow freely from mouth into the sink. Keep unit upright during use for best results.
Turn the unit OFF. Empty any liquid left in the reservoir. If desired, the reservoir may be removed from the power handle by simply pulling down on the reservoir to remove.
Drain unit after use to prevent residual water from leaking out. Tilt unit on it's side and allow water to drain from the drain holes at the top.
NOTE: NOT ALL TIPS INCLUDED WITH ALL MODELS.
The Pik Pocket tip is specifically designed to deliver water or anti-bacterial solutions deep into periodontal pockets.
To use the Pik Pocket tip, set the unit to the lowest pressure setting. Place the soft tip against a tooth at a 45-degree angle and gently place the tip under the gumline, into the pocket.
Set to lowest pressure setting, place tip in the center/middle of your tongue about half way back. Pull forward with light pressure. Increase pressure as you prefer.
To use the orthodontic tip, gently glide tip along gumline, pausing briefly to lightly brush area between teeth and all around orthodontic bracket, before proceeding to the next tooth.
Place the toothbrush tip in mouth with the brush head on the tooth at the gumline. The toothbrush tip can be used with or without toothpaste. Using a light pressure (bristles should not bend) massage the brush back and forth with very short strokes – much like you would with a manual toothbrush.
To use the Plaque Seeker tip, place the tip close to the teeth so that the bristles are gently touching the teeth. Gently glide tip along gumline, pausing briefly between teeth to gently brush and allow the water to flow between the teeth.
When travelling, place travel plug in unit to keep excess water from draining out.
NOTE: Do NOT run unit while travel plug is in unit.
Your Waterpik Water Flosser can be used to deliver mouthwash and antibacterial solutions. For ease of adding other solutions remove the reservoir (see "When Finished" section) and add from opening on reservoir. If you are adding additional water you may replace the reservoir and fill reservoir fully with the fill door. After using any special solution, rinse unit to prevent clogging by partially filling reservoir with warm water and running unit with tip pointed into sink until unit is empty.
Never immerse unit in water. Before cleaning, unplug from the electrical outlet. Clean the product when necessary by using a soft cloth and mild nonabrasive cleanser to wipe exterior. The water reservoir is removable for easy cleaning. It is recommended that the reservoir is removed and cleaned weekly.
Hard water deposits may build up in your unit, depending on the mineral content of your water. If left unattended, it can hinder performance. Cleaning internal parts: add 1 tablespoon of white vinegar to a full reservoir of warm water. Point the handle and tip into sink. Turn unit ON and run until reservoir is empty. Rinse by repeating with a full reservoir of clean warm water. This process should be done every 1 to 3 months to ensure optimal performance.
If the Water Flosser is to be stored for an extended period of time (six months or more), be sure to fully charge it prior to storage. Do not expose the battery or appliance to excessive temperatures.
To remove the rechargeable battery for recycling, please discharge the battery fully before removing.
Observe basic safety precautions when you follow the procedure below. Be sure to protect your eyes, hands, fingers and surface on which you work.
Waterpik Water Flossers have no consumer serviceable electrical items and do not require routine service maintenance. For all parts and accessories go to www.waterpik.com (US) or www.waterpik.ca (Canada). You may also call our toll-free customer service number at 1-800-525-2774 (US) or 1-888-226-3042 (Canada).
Refer to the serial and model numbers in all correspondence. These numbers are located on the bottom of your unit.
Still have questions? Go to www.waterpik.com (US) or www.waterpik.ca (Canada).
SAFEGUARD STATEMENTS
READ ALL INSTRUCTIONS BEFORE USING.
When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
To reduce the risk of electrocution:
To reduce the risk of burns, electrocution, fire, or injury to persons:
SAVE THESE INSTRUCTIONS
SYMBOLS | |||
The following symbols may appear on your product and/or packaging. Some of these symbols may not be relevant in your region and are listed for information purposes only. | |||
Symbol | Definition | Symbol | Definition |
![]() | Do not use this device in a shower, bathtub and do not immerse in any liquid. | ![]() | Detachable Power Supply |
IPX7 or IPX4 | Ingress Protection Code | ![]() | Direct Current (DC) Voltage |
![]() | IEC Class II Equipment | ![]() | Alternating Current (AC) Voltage |
![]() | Do not immerse this device in any liquid. |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the WF-16 and is the answer not in the manual?
Questions and answers