Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Panasonic LP-ADP50
Summary of Contents for Panasonic LP-ADP50
- Page 1 Laser Marker/ Laser Welding Machine Touch Panel Console Instruction Manual LP-ADP50 Please read these instructions carefully before using this product, and save this manual for future use. ME-LPADP50-IM-3 2023.11 panasonic.net/id/pidsx/global...
-
Page 2: Preface
Preface Thank you for purchasing our product. For full use of this product safely and properly, please read this document carefully. This product has been strictly checked and tested prior to its delivery. However, please make sure that this product operates properly before using it. -
Page 3: Cautions In Handling
(that was not meant to be pressed) will be activated. It could lead to a damage to the facility or an accident. • The above are safety precautions regarding the touch panel console LP-ADP50. For "Cautions in Handling" for the laser marker / laser welding machine, refer to the manual for each model. - Page 4 For the Proper Use of Product • Be sure to observe the following matters to prevent a failure or a malfunction of this product and to maintain the product performance properly. „ Environment • Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This might cause malfunction due to induction.
- Page 5 Products) as occasioned by the improvements of Products. Consequently, when you place orders for these Products, Panasonic Industrial Devices SUNX asks you to contact one of our customer service representatives and check that the details listed in the document are commensurate with the most up-to-date information.
-
Page 6: Related Regulations And Standards
*1 : Authorized Representative in EU: Panasonic Marketing Europe GmbH, Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany *2 : UK Address: Panasonic UK, a branch of Panasonic Marketing Europe GmbH Maxis 2, Western Road, Bracknell, Berkshire, RG12 1RT ME-LPADP50-IM-3... - Page 7 „ Attention for the disposal • To dispose of this product, in accordance with the regional regulation, please request the industrial waste disposer. • Dispose of this product as industrial waste, and never discard it with regular trash. • Only for European Union and countries with recycling systems. These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste.
-
Page 8: Table Of Contents
Contents Preface ……………………………………………………………………………… 2 Cautions in Handling ………………………………………………………………… 3 Related Regulations and Standards ……………………………………………… 6 1 Product Overview …………………………………………………… 9 1-1 Package …………………………………………………………………………10 1-2 Specification ……………………………………………………………………10 1-3 Name of Each Component and function …………………………………… 11 1-4 Outer Dimensional Drawing ……………………………………………………12 2 Screen Adjustment …………………………………………………... -
Page 9: Product Overview
1 Product Overview ME-LPADP50-IM-3... -
Page 10: Package
This product is a color liquid crystal display with a touch panel dedicated to our laser marker/laser welding machine. This product is developed/manufactured for use in an industrial environment. Item Specification of LP-ADP50 Power voltage DC24V±10% (supplied from laser marker/laser welding machine) -
Page 11: Name Of Each Component And Function
1-3 Name of Each Component and function Hook hole for wall hanging This is a hook hole used when hanging this product on a wall. Fixing screw hole (8 holes) It is used when fixing this product. You can use either inside 4 holes or outside 4 holes. Connection cable A cable that connects to the controller of the laser marker/laser welding machine. -
Page 12: Outer Dimensional Drawing
1-4 Outer Dimensional Drawing Unit: mm (265) (36) 80±0.2 236±0.2 (227) (15) (54) Description Hook hole for wall hanging: hole size 33mm × 5mm, hook part R3mm Fixing screw hole (8 holes): M4 screw, depth 5, tightening torque: 0.7±0.1N·m You can use either inside 4 holes or outside 4 holes. -
Page 13: Screen Adjustment
2 Screen Adjustment ME-LPADP50-IM-3... -
Page 14: Start-Up The Screen Adjustment Menu
2-1 Start-up the Screen Adjustment Menu When adjusting the contrast or screen position of the touch panel console, display the display setting panel on the touch panel console. While the setting panel for screen adjustment is displayed, screen operation for the laser marker/laser welding machine is disabled. -
Page 15: Screen Configuration
2-2 Screen Configuration The configuration of the setting panel for screen adjustment is shown below. Name Description Menu The menu for the screen adjustment is displayed. Adjustment items The adjustment items for the selected menu are displayed. Setting value The setting values for the selected adjustment item are displayed. -
Page 16: Operation Method Of The Screen
2-3 Operation Method of the Screen The operation method of the setting panel for screen adjustment is shown below. • For operation method of laser marker/laser welding machine using the touch panel console, refer to the manual for laser marker/laser welding machine. ⿎... - Page 17 If you touch “Set” while the cursor is on the left side item, the cursor moves to the right side item and setting contents for the selected menu are displayed. If you touch “Exit” while the cursor is on the right side item, the cursor moves to the left side item. ME-LPADP50-IM-3...
- Page 18 ⿎ Change the setting value When the cursor is on the setting value area on the right side, touching the “-” button once decreases the setting value by one. Touching the “+” button once increases the setting value by one. ⿎...
- Page 19 ⿎ Cancel the change of the setting value If you touch “Exit” after changing the setting value, the setting value returns to the previous value and the cursor returns to the left side item. ⿎ Terminate the screen adjustment If you touch “Exit” while the cursor is in the menu item area, the setting value is saved and the screen returns to the setting screen for the laser maker/laser welding machine.
-
Page 20: Description Of Adjustment Parameters
2-4 Description of Adjustment Parameters 2-4-1 Brightness/contrast Sets the brightness and contrast. Item Description Setting range Default value Brightness Adjusts the brightness level of the backlight. 0 to 100 Contrast Adjusts the contrast level of the screen. 0 to 100 2-4-2 Color settings Sets the contrast of each one of the RGB colors. -
Page 21: Display Settings
2-4-3 Display settings Sets for the analog input. If you change "Display Settings", execute "Touch Panel Calib.". Item Description Setting range Default value H. Position Adjusts the horizontal position of the screen. 0 to 100 V. Position Adjusts the vertical position of the screen. 1 to 63 *1 32 *1 The available setting range depends on the model of the laser marker/... -
Page 22: Touch Panel Settings
2-4-4 Touch panel settings Sets for the touch panel. Item Description Touch Panel Calib. Execute the calibration of the touch panel. After you set the value in the Display Settings menu, it is necessary to execute this operation. If you select “Touch Panel Calib.”, “+” is displayed in the following order on the setting screen for the laser maker/laser welding machine. -
Page 23: Other Settings
2-4-5 Other settings Sets for the screen adjustment panel. Item Description Setting range Default value OSD Transparency Sets the transmission effect of the OSD (on-screen display) 0 to 5 menu. OSD Timeout Sets the time-out period to exit from the OSD menu. 5 to 100 The value can be adjusted in 5-second increments. -
Page 24: Auto Function
2-4-7 Auto function Performs automatic adjustment during analog input. Item Contents Auto Adjust Adjusts the position automatically. There are cases where manual fine adjust is required depending on the resolution or screen display. ME-LPADP50-IM-3... -
Page 25: Maintenance
3 Maintenance ME-LPADP50-IM-3... -
Page 26: Cleaning
3-1 Cleaning If the touch panel console is stained, clean the console according to the following guidelines. • Use a dry, soft cloth for cleaning this product. • If dirt cannot be removed with a dry cloth, use a damp cloth from which water has been squeezed out. •... - Page 27 MEMO...
- Page 28 Panasonic Industrial Devices SUNX Co., Ltd. https://panasonic.net/id/pidsx/global Please visit our website for inquiries and about our sales network. © Panasonic Industrial Devices SUNX Co., Ltd. 2022 - 2023 November, 2023...