Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information. Throughout this guide, dimensions may vary by ± 1/8" Dimensions in parentheses are millimeters unless otherwise specified. 2 | Sub-Zero Customer Care 800.222.7820...
Classic Series Refrigeration Classic Series Models For the new Classic Series refrigeration, Sub-Zero design- ALL REFRIGERATOR / ALL FREEZER MODELS ers and engineers took a fresh look at everything, inside and out. Exterior refinements include redesigned grilles and lower-profile hinges. Inside, new technology in food preservation makes the new Classic Series refrigeration nothing short of revolutionary.
Page 4
Grille: Solid custom panel or pro louvered grille for 84" overall unit height. Dual wide grille for dual installations. overall unit height. Dual wide grille for dual installations. Handles: Custom, tubular, or pro handles. Handles: Custom, tubular, or pro handles. Overlay Flush inset 4 | Sub-Zero Customer Care 800.222.7820...
Page 5
Classic Series Refrigeration Classic Series Design Options STAINLESS STEEL Stainless steel models require no customization. Grille and handle options are available. Grille: Pro louvered grille for 84" overall unit height. Dual wide grille for dual installations. Handles: Tubular or pro handles. Stainless steel subzero.com | 5...
Page 6
" " (67) (67) " " (946) (796) Model CL3650R(ID), CL3650RG, CL3650F Model CL3050U(ID), CL3050UG Overall dimensions are based on stainless steel models. For flush inset applications, add 1/2" to door clearance (13) dimensions. 6 | Sub-Zero Customer Care 800.222.7820...
Page 10
If two units are installed side by side, refer to page 12 for OPENING WIDTH dual standard installations. 30" Model " (749) 36" Model " (902) 42" Model " (1054) 48" Model " (1206) 10 | Sub-Zero Customer Care 800.222.7820...
Page 12
Shaded line represents profile of unit. A dual installation kit is required for this installation. DUAL OPENING WIDTH Two 30" Models " (1518) 30" and 36" Models " (1670) Two 36" Models " (1822) 12 | Sub-Zero Customer Care 800.222.7820...
Page 14
(GFCI) is not recommended and may cause interruption of operation. Receptacle 3-prong grounding-type Installation must comply with all applicable electrical codes. 7" (178) 6" (152) " (1918) FROM FLOOR RIGHT SIDE OF OPENING Electrical supply location 14 | Sub-Zero Customer Care 800.222.7820...
Page 15
Classic Series Refrigeration Plumbing Requirements Locate the water supply line within the shaded area shown PLUMBING REQUIREMENTS in the illustration below. The water supply line should be Water Supply 1/4" OD copper, braided stainless connected to the house supply with an easily accessible steel, or PEX tubing shut-off valve.
Page 16
PANEL MOUNTING KIT panels must be provided. Handle hardware must also be The Sub-Zero custom panel mounting kit eliminates the provided for overlay and flush inset applications. Refer to need for the backer and spacer panels and is avail able Panel Requirements below and the charts on the follow- through an authorized Sub-Zero dealer.
Page 17
Classic Series Refrigeration Custom Panels Overlay Panels ICE AND WATER DISPENSER Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel, and a 1/4" backer For models CL4250SD and CL4850SD, the refrigerator panel. Refer to the illustration below. door panel must include a cutout to accommodate the external dispenser.
Page 20
Refer to the full-scale templates at the end of this guide. When installing two units side by side, refer to page 13 for dual flush inset installations. CUSTOM SPACER PANEL PANEL BACKER PANEL " (19) .10" " TYPICAL Panel assembly (rear view) 20 | Sub-Zero Customer Care 800.222.7820...
Page 21
Classic Series Refrigeration TOP VIEW TOP VIEW TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE DOOR / DRAWER / GRILLE DOOR DOOR DOOR DOOR BACKER CABINETRY BACKER CABINETRY SPACER SPACER TOP VIEW TOP VIEW TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE DOOR / DRAWER / GRILLE PANEL PANEL...
Page 24
Refer to the illustrations below. Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero Customer Care at 800-222-7820.
Page 26
Illus. F " " " " DOOR " " (2) DOOR " SIDE VIEW SIDE VIEW (16) " " " (4) DRAWER SIDE VIEW SIDE VIEW DRAWER " " " SIDE VIEW " SIDE VIEW 26 | Sub-Zero Customer Care 800.222.7820...
Page 27
When installing a Classic Series unit with a custom side wide grille, refer to the charts below. panel, an accessory kit is required. Stainless steel side panels are available through an authorized Sub-Zero DUAL WIDE GRILLE—OVERLAY dealer. For local dealer information, visit the find a show- TWO 30"...
Page 28
Classic Series Refrigeration Standard Handles Optional stainless steel tubular and pro handles are avail- able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for standard handle lengths for Classic Series models.
Page 29
Classic Series Refrigeration Overlay / Flush Inset Panels FULL-SCALE TEMPLATE Overlay and flush inset panels must be a minimum of 3/4" thick to support mounting the handle. Panel thickness (19) does not include the backer and spacer panels. Mount the handle close to the opening edge of the door.
Page 30
Classic Series Refrigeration Overlay Application FULL-SCALE TEMPLATE " (606) OVERALL WIDTH OF UNIT TO REAR OF UNIT 1" (25) THICK PANEL " (19) THICK OVERLAY PANEL (TYPICAL) " (6) BACKER PANEL 0" 1" (25) SCALE 30 | Sub-Zero Customer Care 800.222.7820...
Page 31
Classic Series Refrigeration Flush Inset Application 24" (610) FULL-SCALE TEMPLATE TO BACK WALL For panels thicker than 3/4" , a 90° door stop may be (19) required to prevent interference with adjacent cabinets. " (32) " (56) ASSUMES " (19) FLUSH INSET PANEL THICKNESS...
Page 32
FULL-SCALE TEMPLATE Typical overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. 0" 1" (25) SCALE Dual standard installation (top view) 32 | Sub-Zero Customer Care 800.222.7820...
Page 33
Classic Series Refrigeration FILLER STRIP " (38) " (13) PROFILE OF 3 " (19) FLUSH INSET PANEL DOOR AND TUBULAR HANDLE CLOSED DOOR Dual Flush Inset Installation OPEN 110° FULL-SCALE TEMPLATE Typical flush inset dual installation with filler strip at maxi- mum 110°...
PRO Series Refrigeration PRO Series Refrigeration Freshness finds unmistakable expression with PRO SERIES MODELS Sub-Zero PRO Series refrigeration. A monu- ment to food preservation— equal parts sculpted metal design statement and culinary secret weapon. Its vast interior, like its bold exterior, is crafted of stainless steel.
Page 37
PRO Series Refrigeration Opening Dimensions STANDARD / FLUSH INSTALLATION " OPENING (19) DEPTH TYPICAL " (89) FINISHED RETURN TOP VIEW FRAMELESS CABINETRY " (19) TYPICAL " (89) FINISHED FILLER RETURN OPENING OPENING WIDTH HEIGHT FRAMED CABINETRY SIDE VIEW FRONT VIEW NOTE: 3 "...
Page 38
For flush installations, the face frame will be flush with sur- (51) beyond cabinetry. A dual installation kit is required for this rounding cabinetry. A dual installation kit is required for this installation. installation. 38 | Sub-Zero Customer Care 800.222.7820...
Page 39
Installation must comply with all applicable electrical codes. to the illustrations below. Dual installation kits are available through an authorized ELECTRICAL REQUIREMENTS Sub-Zero dealer. For local dealer information, visit the Electrical Supply 115 VAC, 60 Hz find a showroom section of our website, subzero.com.
Page 40
A copper line is not recommended for this application. Installation must comply with all applicable plumbing codes. RIGHT SIDE OF OPENING 6" " (152) (132) 3" (76) AREA EXTENDS 1 " (13) FORWARD ON FLOOR Water supply location 40 | Sub-Zero Customer Care 800.222.7820...
Page 41
PRO Series Refrigeration Standard Handles Optional stainless steel pro handles are avail able through an authorized Sub-Zero dealer. For local dealer informa- tion, visit the find a showroom section of our website, subzero.com. Refer to the chart below for standard handle lengths for PRO Series models.
Designer Series Refrigeration Designer Series Refrigeration With custom front panels and hardware, COLUMN MODELS Sub-Zero Designer Series columns, tall, and drawer wine models disappear into the decor. Units fit flush with cabinetry, making Designer Series refrigeration as practical and beautiful in the master suite, bar, or theatre room as in the kitchen.
Page 44
IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. " 84"* (1140) (2134) " (10) " (338) " (10) " (268) *HEIGHT DIMENSION ± 1 " " (13) (92) " (45) " (451) 44 | Sub-Zero Customer Care 800.222.7820...
Page 45
Designer Series Refrigeration Overall Dimensions DRAWER DRAWER 24" Drawer 24" (610) " 24" (610) 27" Drawer 27" (686) 30" Drawer 30" (762) " (338) 36" Drawer 36" (914) " "* (10) (876) " (268) IMPORTANT NOTE: Overall dimensions do not include panels or handles.
Page 46
If a dual installation kit is not specified, a minimum 2" filler strip is required between the units. (51) Dual installation kits are available through an authorized Sub-Zero dealer. For questions regarding the installation, SIDE VIEW FRONT VIEW call Sub-Zero Customer Care at 800-222-7820. NOTE: 3 "...
Page 47
Designer Series Refrigeration Electrical Requirements Locate the electrical supply within the shaded area shown ELECTRICAL REQUIREMENTS in the illustration and chart below. A separate circuit servic- Electrical Supply 115 VAC, 60 Hz ing only this appliance is required. Service 15 amp dedicated circuit IMPORTANT NOTE: For indoor models, a ground fault cir- Receptacle 3-prong grounding-type...
Page 48
3" (76) 24" Model 5 1/2" (140) 30" Model 6" (152) 36" Model 9" (229) RIGHT SIDE OF OPENING 6" (152) 3" (76) AREA EXTENDS 1 " (13) FORWARD ON FLOOR Water supply location 48 | Sub-Zero Customer Care 800.222.7820...
Page 49
Designer Series Refrigeration Stainless Steel Panels The outdoor model requires the use of Sub-Zero stainless Reveals between panels can vary, 1/8" reveals are typical. steel outdoor accessory panels. CAUTION The thickness of indoor stainless steel panels is 3/4" (19) As reveals between cabinetry and the unit decrease, outdoor stainless steel panels is 1 1/2"...
Page 50
PANEL WIDTH 18" Model 17 3/4" (451) 24" Model 23 3/4" (603) 27" Model 26 3/4" (679) 30" Model 29 3/4" (756) 36" Model 35 3/4" (908) 50 | Sub-Zero Customer Care 800.222.7820...
Page 51
Toe kick heights from 2" to 3 7/8" require a reduced (51) (98) toe kick accessory available through an authorized Sub-Zero dealer. For questions regarding the installation, call Sub-Zero Customer Care at 800-222-7820. " (45) A DECORATIVE VALANCE CANNOT EXTEND "...
Page 52
Designer Series Refrigeration Standard Handles Optional stainless steel tubular and pro handles are avail- able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for standard handle lengths for Designer Series models.
Page 53
Designer Series Refrigeration Maximum Door Opening FULL-SCALE TEMPLATE As the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by using the 90° door stop. " (19) PANEL DOOR OPEN MAXIMUM 105° " (3) REVEAL POTENTIAL DOOR CLOSED...
Wine Storage Wine Storage Wine finds a well-deserved place of honor in WINE STORAGE MODELS a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced racks, soft lighting, custom cabinetry if desired—Sub-Zero helps make a...
Page 57
Dual Installation UNDERCOUNTER WINE Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the If two units are installed side by side, a dual installation kit find a showroom section of our website, subzero.com.
Page 58
28 1/2" (762) (143) (724) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel " 84"* thickness. (1765) (2134) *HEIGHT DIMENSION ± 1 " " (13) (92) " (45) 58 | Sub-Zero Customer Care 800.222.7820...
Page 59
Wine Storage Overall Dimensions TALL TALL WINE 30" Tall 30" 5 5/8" 28 1/2" (762) (143) (724) 24" (610) " (114) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. " 84"* (1140) (2134) "...
Page 60
(51) Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero Customer Care at 800-222-7820.
Page 61
Wine Storage Overall Dimensions IMPORTANT NOTE: Overall dimensions are based on MODEL CL3050W the stainless steel model. For flush inset applications, add 30" " (762) (665) 1/2" to door clearance dimensions. (13) 84" (2134) " (1911) HEIGHT DIMENSIONS ± 1 "...
Page 62
(89) Shaded line represents profile of unit. If two units are installed side by side, refer to page 64 for OPENING WIDTH dual standard installations. CL3050W 29 1/2" (749) 62 | Sub-Zero Customer Care 800.222.7820...
Page 64
A dual installation kit is required for this installation. DUAL OPENING WIDTH Two Models CL3050W 59 3/4" (1518) CL3050W and 30" Classic Series Model 59 3/4" (1518) CL3050W and 36" Classic Series Model 65 3/4" (1670) 64 | Sub-Zero Customer Care 800.222.7820...
Page 66
OPENING 7" " (178) (114) " 6" 5" 2" (108) (152) (127) (51) FLOOR " " " (1918) 4" FROM FLOOR (102) FLOOR RIGHT SIDE Designer Series models OF OPENING Undercounter Wine Model CL3050W 66 | Sub-Zero Customer Care 800.222.7820...
Page 67
Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for PANEL DIMENSIONS glass and solid door panels.
Page 68
Interference may be dimensions in the illustration below. For questions minimized by using the 90° door stop. regarding the installation, call Sub-Zero Customer Care at 800-222-7820. DOOR OPEN MAXIMUM 115°...
Page 69
Service may be required to install the door. Contact an authorized Sub-Zero dealer Finish all sides of the custom panels. They will be visible for more information.
Page 71
Toe kick heights from 2" to 3 7/8" require a reduced toe kick accessory (51) (98) available through an authorized Sub-Zero dealer. For ques- tions regarding the installation, call Sub-Zero Customer Care at 800-222-7820. " (45) A DECORATIVE VALANCE CANNOT EXTEND "...
Page 72
Stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.
Page 73
Wine Storage Custom Panel—CL3050W FLUSH INSET FLUSH INSET PANEL DIMENSIONS The flush inset application is an overlay model with flush inset panels. It is not a separate model. The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 3/4"...
Page 74
" (16) " DOOR / DRAWER " DRAWER " " " DOOR " (2) DOOR " SIDE VIEW " (16) " (4) DRAWER SIDE VIEW DRAWER " " " SIDE VIEW " SIDE VIEW 74 | Sub-Zero Customer Care 800.222.7820...
Page 75
(2134) opposite hinges. Refer to the illustrations below. Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero Customer Care at 800-222-7820.
Page 76
" " " " " DOOR " " (2) DOOR " SIDE VIEW SIDE VIEW (16) " " " (4) DRAWER SIDE VIEW SIDE VIEW DRAWER " " " SIDE VIEW " SIDE VIEW 76 | Sub-Zero Customer Care 800.222.7820...
Page 77
Standard Handles SIDE PANEL Optional stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. For local The custom side panel must be a minimum of 24" (610) dealer information, visit the find a showroom section of deep and 1/2"...
Page 79
Wine Storage Overlay / Flush Inset Panels—CL3050W FULL-SCALE TEMPLATE Overlay and flush inset panels must be a minimum of 5/8" thick to support mounting the handle. Panel thickness (16) does not include the backer and spacer panels. Mount the handle close to the opening edge of the door. DEPTH OF TUBULAR AND PRO HANDLES 1"...
Page 80
FULL-SCALE TEMPLATE " (606) OVERALL WIDTH OF UNIT TO REAR OF UNIT 1" (25) THICK PANEL " (19) THICK OVERLAY PANEL (TYPICAL) " (6) BACKER PANEL 0" 1" (25) SCALE 90° door opening (top view) 80 | Sub-Zero Customer Care 800.222.7820...
Page 81
Wine Storage Flush Inset Application—CL3050W 24" (610) FULL-SCALE TEMPLATE TO BACK WALL For panels thicker than 3/4" , a 90° door stop may be (19) required to prevent interference with adjacent cabinets. " (32) " (56) ASSUMES " (19) FLUSH INSET PANEL THICKNESS 1"...
Page 82
FULL-SCALE TEMPLATE Typical overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. 0" 1" (25) SCALE Dual standard installation (top view) 82 | Sub-Zero Customer Care 800.222.7820...
Page 83
Wine Storage FILLER STRIP " (38) " (13) PROFILE OF 3 " (19) FLUSH INSET PANEL DOOR AND TUBULAR HANDLE CLOSED DOOR Dual Flush Inset Installation—CL3050W OPEN 110° FULL-SCALE TEMPLATE Typical flush inset dual installation with filler strip at maxi- mum 110°...
DEU2450R DEU2450CI DEU2450BG DEU2450RADA DEU2450BGADA in any room or outdoor kitchen. They are ready to be fitted with a custom or stainless steel panel. DEU2450RO DEU1550BG DEU1550B 84 | Sub-Zero Customer Care 800.222.7820...
Page 86
OPENING WIDTH HEIGHT to the illustrations below. Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero SIDE VIEW FRONT VIEW Customer Care at 800-222-7820.
Page 87
Designer Series Undercounter Refrigeration Electrical Requirements Locate the electrical supply within the shaded area shown CAUTION in the illustration below. A separate circuit servicing only The outlet must be checked by a qualified electrician this appliance is required. to be sure it is wired with the correct polarity. Verify the outlet is properly grounded.
Page 88
The outdoor model requires the use wall or place it in an adjacent cabinet. Locate the water of a Sub-Zero stainless steel outdoor accessory panel. For supply line within the shaded area shown in the illustra- local dealer information, visit the find a showroom section tion below.
Page 89
DUAL INSTALLATION tered top to bottom. Stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For For dual installations, refer to the chart below for typical local dealer information, visit the find a showroom section panel dimensions.
Page 90
Interference may be dimensions in the illustration below. For questions minimized by using the 90° door stop. regarding the installation, call Sub-Zero Customer Care at 800-222-7820. DOOR OPEN MAXIMUM 115°...
Page 91
Designer Series Undercounter Refrigeration Standard Handles Optional stainless steel tubular and pro handles are avail- able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for standard handle lengths for Designer Series Undercounter models.
Undercounter Ice Maker Undercounter Ice Maker In the kitchen, bar, or media room, a Sub-Zero ICE MAKER MODELS high-volume ice maker is a must for entertain- ing. The design flexibility of this compact unit allows it to fit in any room or outdoor kitchen.
Page 94
Electrical supply location 8" (203) " 24" ( 13 ) (610) ROUGH LOCATION OF OPENING WATER LINE DEPTH TOP VIEW Water supply location " min (387) ROUGH OPENING WIDTH 94 | Sub-Zero Customer Care 800.222.7820 " (876)
Page 95
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
Page 96
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. If the owner uses Sub-Zero Factory Certified Service, the service provider will repair or replace these parts with the owner paying for all other costs, including labor.
Page 97
FULL ONE YEAR WARRANTY** For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero Factory Certified Service, unless otherwise specified by Sub-Zero, Inc.