Table of Contents
Advertisement
Connections
and Se u E
Install Batteries
in the Remote
I.
Remove the battery compartment
cover on the back of the remote.
2.
Insert new batteries. M_tch the polarities (+ and -) on the batteries with the diagram on the remote.
3.
Put the battery compartment
cover back on the remote.
Important Battery Information
• ffyou're not going to usethe remote for a month or more, be sure to remove the batteries becausethey can leak and cause damage.
• Disposeofbatterles in the proper manner,according to federal,state, and local regulations.
• Any battery may leak electrolyte if mixed with a different batterg _ype,Jflnserted incorrectly,ffa# batteries are not replaced at the samet_me,ifdlspased ofln fro, or if an
attempt is made to charge a battery not intended to be recharged.
• Discard leaky batterles _mmediately. L eakingbatterles can cause skin burns or other personal injury.
Point the Remote
in the Right Direction
and Put it in DVD Mode
When
you want
the remote
to operate
the DVD
Recorder,
point
the remote
_ the
DVD
Recorder,
not the TMTbe
remote
has to be pointed
in the
correct
direction
and toward
the correct:
component
in order
for the remote
control's
signal to communicate
with
the sensor
on the component.
Make
sure there
is a dear
path
between
the remote
control
and the component
you want
to operate,
so the signal isn't
blocked.
Make sure the remote is in DVD mode --- press the DVD button.
Turn on theTV
and DVD Recorder
I.
Turn on the DVD Recorder_ress
the DVD button on the remote.
2. Turn on the TV and tune it to the correct Video Input Channel_if
you have an RCA, GE, or Proscan TV,, press the TV button on the remote and then
press the INPUT button on the remote (theTV
turns on and tunes to the correct Video Input Channel).
If you have another brand of T_, turn on theTV and tune the TV to the correctVideo
Input Channel (if you don't know how to access theVideo
Input
Channel on your TV.go to page 15 for help).
Note:Youcan program your remote to operate most brands of remote controllableTVs.Instructionsare on page 2 I.
Le_
arrow
buit0n
buit0n
. _
drrow
bulion
R_i _rrow
b_t_0n
Use the _'1"o_ but_ns
on the remote to
move through
on-screen
n'lenu$ and
highlight different options. Press the OK
button
to select a menu item that is
highlighted.
Complete the Interactive Setup
The next few pages step you through the series of screens that will appear the first time
you turn on your DVD Recorder,
Use the remote control to follow the on-screen instructions.The
arrow buttons move the
on-screen highlight in the corresponding
directions
on the screen (up, down, left, right).
Press the OK button to select a highlighted item.
Notes:
Youcan accessthe setup screensfrom the main menu. If you move,get a different program provider for
TV shows,or changepour connections, y ou'# needto complete the Interactive Setupagain.
If you don't see the Language selection
screen (below) the frst time you turn on the DVD Recorder,
make sure you've tuned your TV to the Video Input Channel that corresponds
to the way you've
connected the TV to the DVD Recorde_ If you need help, go to page t 6.
ilish
I) Select
on-screen
menu language
Make sure the remote
is in DVD mode (press the DVD button). If you want the on-
screen menus to appear in English, press the OK button on the remote control. If
you prefer another language,press the arrow down button until that language is
highlighted. Press OK to select the language.
Note: ff you don't see the Language selection screen the first time you turn on the DVD Recorder, make
sure you've tuned y0ur TV to tba VJdeo Input Channel that corresponds
to the way you've connected the
TV to the DVD Recorde_ If you need help, go to page 15.
12
Graphics
contained
within
this publication
_re for representation
only.
Advertisement
Table of Contents
