Table of Contents
Advertisement
XAV-W600/W650BT
(US, CND)
Connection/Installation
Cautions
Run all ground (earth) leads to a common
ground (earth) point.
Do not get the leads trapped under a screw or
caught in moving parts (e.g., seat railing).
Before making connections, turn the car ignition
off to avoid short circuits.
Connect the yellow and red power supply leads
only after all other leads have been connected.
Be sure to insulate any loose unconnected leads
with electrical tape for safety.
Precautions
Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).
For details on using the wired remote control, see
.
"Using the wired remote control" (page 36).
*5 Whether in use or not, route the microphone input
cord so it does not interfere with driving operations.
Secure the cord with a clamp, etc., if it is installed
around your feet.
*6 For details on installing the microphone, see
.
"Installing the microphone" (page 35).
*7 Such as a portable media player, game console, etc.
Making connections
To a common ground (earth) point
First connect the black ground (earth) lead, then
connect the yellow and red power supply leads.
To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
To a car's illumination signal
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
12
SECTION 2
GENERAL
Connection
White
White/black striped
Gray
Gray/black striped
Green
Green/black striped
Purple
Purple/black striped
Black
Yellow
Red
Blue/white striped
Orange/white striped
Light green
Purple/white striped
To the parking brake switch cord
The mounting position of the parking brake
switch cord depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply connection cable
to the parking brake switch cord.
Parking brake switch cord
Hand brake type
To the +12 V power terminal of the car's rear
lamp lead (only when connecting the rear
view camera)
*
*
*
*
*
*
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms
and with adequate power handling capacities to
avoid damage.
Monitor connection
When installing a monitor for the rear seat, connect
Foot brake type
its parking brake switch cord to the ground (earth).
This section is extracted
from instruction manual.
Subwoofer*
3
3
3
Power amplifier*
1
Portable audio/
3
video device*
1
*
7
3
Rear view camera*
1
3
Monitor*
1
*
5
*
6
from a wired remote control (not
*4
supplied)
Front speaker*
1
*
2
1
2
Rear speaker*
*
For details, see "Making
.
connections" (page 35).
from a car antenna (aerial)
1
Advertisement
Table of Contents
