Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
INSTALLATION
INSTRUCTIONS
DESIGNER SERIES
MICROWAVE BUILT-IN TRIM KIT
Retain for Future Reference
IMPORTANT - PLEASE READ AND FOLLOW
• Before beginning, please read these instructions completely and carefully.
• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.
Remove the turntable from the oven cavity.
• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• The installer should leave these instructions with the consumer who should retain for local inspector's use and for future
reference.
THIS BUILT-IN TRIM KIT IS DESIGNED FOR USE ONLY WITH VIKING MICROWAVE OVENS SPECIFYING BUILT-IN
TRIM KIT DMTK271 OR DMTK301 ON THE RATING LABEL ON THE LEFT SIDE WALL OF THE OVEN CAVITY.
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
PARTS INCLUDED IN THE KIT
1) Frame Assembly
Front Frame
QTY 1
3) Screw A (1-3/16" length): QTY 2
Back Frame
QTY 1
4) Screw B (1 3/4" length): QTY 4
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
2) Bottom Duct Assembly: QTY 1
NOTE:
SIDE FLANGES ON
DMTK301 ONLY.
5) Template: QTY 1
Maximum Cutout Opening Width 24 11/16" (627.06 mm)
Minimum Cutout Opening Width 24 3/8" (619.13 mm)
BUILT-IN TRIM KIT TEMPLATE
FOR DESIGNER SERIES MICROWAVE OVEN
Center Line
Distance between holes
28 5/8" (727.3 mm)
14 5/16" (363.475 mm)
Distance between holes
25 5/8" (650.75 mm)
12 13/16" (325.4 mm)
Floor Line of Cutout Opening
29/32" (23.4 mm)
1. Align the mounting template center line with the center of
the cutout and the floor line with the floor of the cutout.
Tape it into place.
2. For DMTK271, predrill 4 holes marked
with a " drill bit.
For DMTK301, predrill 4 holes marked
with a " drill bit.
3. Remove template from the cabinet
TINSKB110MRR0
Advertisement
Related Manuals for Viking Designer DMOS200SS
Summary of Contents for Viking Designer DMOS200SS
-
Page 1: Parts Included In The Kit
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE. -
Page 2: Cabinet Or Wall Cutout
CABINET OR WALL CUTOUT Cutout Dimensions Height (A) Minimum Maximum Width (B) Minimum Maximum Depth (C) Minimum ELECTRICAL OUTLET LOCATION Outlet should NOT be in the shaded area as indicated on Illustration 1. NOTE 1: If the Depth (C) dimension is greater than 1" (53.3 cm), the outlet location may be in any area on the rear wall. NOTE 2: The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven. Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling and rear partition. The proper functioning of the oven does not require the enclosure. MOUNTING TEMPLATE 1. Align the mounting template center line with the center of the cutout and the floor line with the floor of the cutout. Tape it into place. -
Page 3: Cabinet Installation
CABINET INSTALLATION 1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet. . Carefully guide the assembled oven into the prepared opening. Slide the oven on the Bottom Duct Assembly. See Illustration 3. Avoid pinching the cord between the oven and the wall. Adjust the position of the oven so that the feet of the oven are fitted into the recesses of the Bottom Duct Assembly. See Illustration 4. FRAME INSTALLATION Position the BACK FRAME to align with the predrilled holes that were drilled with the mounting template. Check that it is level and then secure with four SCREWS B. See Illustration 5. Illustration 5 SCREW B SCREW B OVER OVEN INSTALLATION See illustration 7. Illustration 4 Place the FRONT FRAME, with tabs on top, onto the BACK FRAME. Secure the FRONT FRAME to the BACK FRAME by firmly pushing the front frame onto the back frame engaging the four (4) snap attachments. See... - Page 4 18-5/8” (47.3 cm) Overall 2.0 cu. ft. 120VAC/60 Hz 1.5 KW 13 amps 46 lbs. (20.9 kg) Viking Range Corporation Specifications subject to change without notice. Built-In Trim Kits DMTK271 DMTK301 26-1/2” (67.3 cm) 29-1/2” (74.9 cm) 18-1/4” (46.3 cm) 18-1/4”...