Advertisement
Quick Links
TECHNICAL
TECHNICAL
T
T
E
L
E
E
L
E
The SC-911 Strobe Controller connects in parallel with your phone line and
passively listens for touch-tones. When 911, 9-911, 8-911, or the custom acti-
vation number is detected, the SC-911 flashes the built-in 0.75" LED and acti-
vates a 12VDC switched output capable of running an emergency strobe light.
A strobe light can get help to you when you need it most, providing the emer-
gency services with a clearly visible beacon to locate your home as fast as pos-
sible, and also alerting neighbors or nursing staff of your need for assistance.
The built-in LED is useful for indoor applications, such as apartment complex-
es, schools, offices and assisted living housing.
The SC-911 comes complete with a 12VDC power adapter, and also provides
a set of relay contacts for user application.
P
P
F
e
a
t
u
r
e
s
F
e
a
t
u
r
e
s
• Detects "911", "9911", "8911", "555" (test) calls and/or a
custom activation number
• Bright 0.75" red LED visible over 100 ft
• Switched 12VDC output for powering strobe lights,
cameras, etc.
• One set of (N.O.) normally open or (N.C.) normally
closed relay contacts provided
• Wall mountable with foam tape (included) or screws
(not included)
• Reset by dialing any touch-tone or programmable
output timer
• Contact closure activation and reset function
M
o
u
n
t
i
n
g
M
o
u
n
t
i
n
g
A. Using Screws
(not included)
Step 1. Unsnap the plastic cover and remove the top screw holding the circuit board.
Step 2. Remove the circuit board, exposing the two mounting holes in the base.
Step 3. Screw the base to the wall, etc. using (2) #6 flathead or sheetrock screws.
Note: Make sure the screw heads are fully driven into the base to avoid
shorting the circuit board leads.
B. Using the Included Tape
Step 1. Clean the back of the SC-911 and the surface you are mounting to with
rubbing alcohol before mounting.
Step 2. Remove the backing on one side of the tape and adhere to the SC-911.
Remove the rest of the backing and press unit firmly to surface you are
mounting to.
S
S
C
O
M
O
L
U
T
I
O
N
S
C
O
M
O
L
U
T
I
O
N
S
Activate a Strobe Light with a Call to 911
Save valuable seconds on EMS response times!
h
o
n
e
.
.
.
7
1
5
.
3
8
6
.
8
h
o
n
e
.
.
.
7
1
5
.
3
8
6
.
8
P
r
a
c
P
r
a
c
2
1
C
2
1
C
F
O
R
T
H
E
S
T
F
O
R
T
H
E
S
T
A
p
p
l
i
A
p
p
l
8
6
1
8
6
1
• Turn on a strobe light with a 911 call
• Trigger a doorstrike to enable quick and easy EMS access to
your home
• Notify security in a gated community to allow EMS access
• Alert local nursing staff to an emergency call
S
p
e
c
S
p
e
c
Power: 120VAC to 12VDC UL listed adapter provided
Dimensions: 74mm x 53mm x 36mm (2.9" x 2.1" x 1.4")
Shipping Weight: 0.4kg (0.86lbs)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-
condensing humidity
LED: 20mm (0.75") diameter, red
Visibility: 30m (100 ft) typical
Relay Contact Rating: .5A @ 125VAC / 1A @ 30VDC
Maximum Current Draw Switched 12VDC Output: 350mA
Connections: 9 position screw terminal block
SC-911
SC-911
Strobe Controller
t
i
c
e
t
i
c
e
February 6, 2008
E
N
T
U
R
Y
E
N
T
U
R
Y
c
a
t
i
o
n
s
i
c
a
t
i
o
n
s
i
f
i
c
a
t
i
o
n
s
i
f
i
c
a
t
i
o
n
s
(2) #6 Flathead Screws
or Sheetrock Screws
Mounting
Holes
Advertisement
Related Manuals for Viking SC-911
Summary of Contents for Viking SC-911
- Page 1 B. Using the Included Tape Step 1. Clean the back of the SC-911 and the surface you are mounting to with rubbing alcohol before mounting. Step 2. Remove the backing on one side of the tape and adhere to the SC-911.
- Page 2 ** Note: The custom number cannot start with a “ Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no respon- sibility for errors and omissions contained in this information.